Viewing all customer Discussions for:

15-002 Channel Balance Shoe, 1" Depth

I have non-tilt sliding windows with 27" channel balances (I think). They have been non-operational since I purchased my house and I dont have any knowledge of the make/model other than "IWC" logo on the latch. I tried to re-attach the balances, but they won't stay attached. It feels like the spr ... (cont.)

This is in regards to the above order. Just want to make sure I am ordering the correct parts. 28 3 Caldwell LL is stamped on the metal. It measures from metal to metal at 29". The metal is beveled at the edges. The window weighs approx. 20 lbs. Happy to answer any other questions. Thank you. ... (cont.)

the ones i have are 18-166 and 16-002. i also have the rivets and the rivet tool. the piece i need now goes on the bottom of the window on the metal piece.

My windows are made by Alenco, and I'm assuming they were the originals in this home Lancaster California built in 1989. They are worn out and need to be replaced. I'm attaching photos of one of the balances. And here are the measurements: length from plastic tip to tip = 29" (metal only is 28" lon ... (cont.)

I need help on what needs to be ordered. I've attached pictures to help identify the parts. Your video's are quite helpful and are the reason I'm contacting you for replacements. 3 - marked with 2840 2 - marked with 2830 Thanks, Greg

I need some replacement balances. The channel is 1/2" by 5/8" with an outside hemmed edge. The writing on the back is "28 3 10 CALDWELL" The metal channel is 29" long NOT including the plastic fittings. I am pretty sure the top fitting is 19-002 because it does not have flanges. The bottom sho ... (cont.)

I need two channel balances as pictured. The numbers on the existing: 16 1 BSI RN The measurements are shown and are 18 inches end to end- 16 and 7/8 inchs metal to metal.

I have a Kinco window that I need to replace both channel balances. The existing balance is stamped 29 3 IP Caldwell. The existing channel top matches your 19-005 and the bottom shoe matches your 15-002. Do you offer a balance in this configuration? Thank you.

Need to identify parts

I need to replace my channel balances for my Viking windows. The balances I have are 29 inches in length and 1/2 inch width. They have a stamp on them that says 2830n (or upside down u). I have sent pictures of the hardware on both ends.

I need two Channel Balance for a non tilt window, width is 1/2" and length is 31" from just ends of metal case. Numbers and letters on metal case: 30 4 HV CMC 7. I have additional photos if you need to see more.

I'm having trouble with the stamp option. I need to replace 4 balances for 2 different windows. One is stamped 28 1/4 3 E H, and the other is stamped 28 1/4 3 C H. Can you ID. The correct ends for me too? I would really appreciate it. Can you help me find the right replacements? Ray ... (cont.)

This is a bathroom non-tilting PGT window with laminated glass. The balance has what appears to match your 19-005 top guide and a 15-002 bottom shoe. I do not see this combination, do you have recommendations or a better identifcation from the provided pictures?

The balancer I removed are marked 25 9 37# 19" LT JQ Caldwell Upper plactic has wings but lower plactic pieces dont

The length of the metal portion without the clips is 25 inches. I need to buy a large quantity as well as a lot of take out clips. 2430

I am looking to buy two matching (left and right) channel balances as shown in the pictures. I could not identify the ends in the ones shown in your web page. I am guessing that the double-pane windows weight about 30 pounds or so. The length of the metal "U" shaped channel is 28". The width of ... (cont.)

Hi - I have a sash non-tilt sliding window that has two broken channels on it (the hooks broke off which renders them useless). The home was originally built by Ryland Homes and the windows are made by BFS, at least that's what's stamped into the locks. They have not been replaced since we are the o ... (cont.)

I need to replace a pair of balances on one window. It has never worked since we moved in. As seen in the photos, they are 30" long, stamped with 2990EG B.S.I. 32 In the photos showing the end attachments, it shows both balances side by side. Please help me figure out the correct balance for my ... (cont.)

I have a 26" channel balance that has a shoe that doesn't match any of your option. Plus from the photo of the stamp on the channel, does that indicate what type of weight I might need?

I believe that I have a Series 351 with a 15-002 Shoe and a 19-002 Top. Please see photos to verify. It is hard to see the difference between the 15-002 and the 15-001 Shoes in your photos. The Top & Shoe are almost the same color with the Shoe being slightly more yellow. The only marking is "2 ... (cont.)