Viewing all customer Discussions for:

15-002 Channel Balance Shoe, 1" Depth

Thanks for your prompt response Attached please find new pictures as requested. Magazine , should you need any further information , please let me know ASAP as I need them urgently Hope this will clarify the reference needed do I can place the order Waiting for your instructions

Hello, Here are the pictures. 1. I need to replace the balance track. 20" tall, and the header and foot as shown. The balance shows 2140.I know we have integral with header and foot, please tell me the part number separately. (balance, header, shoe in case in the future use) 2. I need to buy some ... (cont.)

I think the tops I can identify. But the bottom don?t seem to be pictured on you site

Hello, I need help identifying parts for a window balancer for a Florida Extruders International - Milestone single series 1000 window. It appears to be 30 inches from one end to another with the"UB 28D" marking on it. I have attached pics and can provide more if needed. Thank you ... (cont.)

Kindly advise your equivalent of above Caldwell Window Channel Balance. Thanks.

Hello, I need four spring powered channel balances for my two front windows. Their design seems problematic using pulleys and an extension spring. The spring is quite powerful and wore, then pulled through the double pulley block anchor hole. They are all 1/2"wide x 24" long. All four failed ... (cont.)

This is a Traco window. The spring balance channel is 9/16 inch wide and 18 inches long. These are the markings on the side of the channel. 17DS 29 BSI VM If you need other photos to match up this part please let me know as soon as possible. Thank youl

I need two channel balance replacements for 24 4 GN Caldwell. I have identified them as Series 351 (25"), Top Guide 19-002, and Shoe 15-002, with the 2440 option (19-24 lbs.). Is this correct?

HI - I need to replace channel guides for two of my single-hung, non-tilt windows. Number stamped on part seems to be 1210P. It is 12.5 inches long (not 12 or 13). Guide width seems to be narrower (1/2 inch) in front, and a little wider in back (5/8)..not sure if that is the original width or if it ... (cont.)

Could you provide the item numbers for the bottoms and tops for the Yale-Ogron channel balance ends?

Stamped 2330 24" the top guide was broken so hoping you can identify, bottom shoe is in picture.

I need 2 each Channel Balance Assemblies. Markings on old assemblies appears to be 27C, however when measuring the metal portion of the Channel itself, end-to-end, it measures 28". I went to Southwest Glazing Supply Company in Dallas, TX and they said there part number for this was 2740 or 27D ... (cont.)

Replacement part for window, left side slide mechanism broke.

Good afternoon, I would like to order 2720 channel balances. I am not sure which ones to order I have included pictures..

Please help identify and by two of these. I know they are 1/2 inch wide and 28 inches long. But the ends did not match any on your web site.

I need to replace broken Block and Tackle Window Balances. Do not know who is the window manufacturer. It is a non-tilt window and side load. Measurement is 15" and a 9/16" channel. The window has a label w Mfg Code YOM-1 Series 9500. Window H-R50 53x74 The marking on the broken one is 14 ... (cont.)

I have old viking windows and need to replace the balance on many of them. On the window frame I found the label: Viking industries Spec: DH-B1-HP (45) Series: 80/85 MST: 4066 On one of the balances I saw 2830 marked. On another 2280. Is there a difference between 2830 and 2280? It is a h ... (cont.)

Window slider spring for raising and lowering window. I do not have any identifying part numbers. Window slider spring goes on inside channel of window. Measures:1/2" x 1/2" x22" in length.

Need 2 window balances 24" with top and bottom caps As shone in pics. Thxs carl

The number 2330 and what seems like a partial "5" seems to be stamped on the front bottom. The metal balance is 24" in length and 9/16" width. The plastic clip on the top is 1.25" The total length from bottom plastic to top plastic is 25 9/16"