Viewing all customer Discussions for:

15-004 Winged Channel Balance Shoe, 1-3/32" Depth

I need to order two different block and tackle glances for a few windows. Here is what I can find on the parts: First set: Lettering on the unit 30 9 BR CAELDWELL, Length 31", Width 1/2 " see pictures attached. I need four of them Second set: Lettering on the back 20 E 15, Length 29", Width 1/ ... (cont.)

What is the appropriate replacement balancing spring please? Metal portion of shaft is 33" and width is 1/2". Sash weight is 27 pounds. If I went with the option where it's rated 28-32 pounds does that mean a higher spring tension will make it easier to lift yet harder to close? These windows have ... (cont.)

I am a returning customer needing to buy two replacement channel balances for a Jordan non-tilt window in my home. The window sash measures 30 1/4" H x 28 7/16" W and weighs 20lbs. 14.5ozs. The numbers stamped on the side of the old balance are 28-3 and K 1. I think this is a series 390 bal ... (cont.)

On the !5-004 and 15-005 is the measurement from the inside of the wing or outside?

I need 2 window balances the same 27 inches long with the plastic pieces. The numbers are on the one that I sent to you. Thank you Mike's property maintenance

Picture 1 shows the stamp on the slide 28D Picture 2 shows the length of the METAL rod = 29" Picture 3 shows the width 9/16 Picture 4 shows the depth 1/2 Picture 5 shows the clip

Hello, I have windows that are approx. 9 years old bearing the labels: Series:Mark 40/50 Premium STD - AAMA/NWWDA 101/ I.S. 2-97 - H-LC25/35-52X96. The retainers that keep the spring loaded balance are breaking at the top and allowing the balance to move out of the window. Need replacement caps ( ... (cont.)

Help! I've become one of those people with a piece of wood holding my window open. The length of my existing balance (just the metal) is 27" and the width is

Please advise for replace center balance, marked "25 3 JU 7"

I have two sets of window channel sets I need. The first channel is a 2720 bsi. It measures metal to metal 28" long. THe second channel is stamped 2130 bsi. It measures 22" long metal to metal tip to tip. I am also in need of the plastic stops that go at the top of the window. They are black plasti ... (cont.)

15in x 0.5 in. 1402 weight. Need a match.

We are looking for parts for three Kenco windows. We have a 29" balance and are looking for - 2 springs and 6 retainers that screw onto the top of the window. I have a few more photos than what is attached and can send them if needed. Series Mark 40/50.

Hi, I'm having trouble finding the replacement parts for my sash window balance. The balance is 1/2'' wide. I would also need to purchase the shoes, top, and sash guide. Hopefully the shoes and top are standard replacement, the sash guide is very difficult to identify, so I've included some photo ... (cont.)

My customer is looking to get some of these. Customer states the following number is on the shank. 26-4 AA CMC 11 Please advise Wayne

Hello, I would like to replace the two channel balances in a sash window. I have attached pictures of the existing balance. The metal part is 28" long (excluding the plastic end caps) and is stamped "2730". The window is an aluminum frame, original install in a house built in 1986 in California. ... (cont.)

I need assistance selecting the correct replacement sash spring. The existing metal channel is 33" long. Sash weight is 23#. See attached photos Thanks Eric

I'm trying to find the correct window balancer to replace one that broke. It is 14" and the only stamp on the side says "13 2 CO CALDWELL" (could possibly be CD). Pictures of both ends are also attached. I tried to select the correct part myself but I could not identify the subtle differences in s ... (cont.)

I need to replace my Channel balance and need to make sure I get the one with the correct ends. I have attached pictures of each end. On the channel itself, it has the number 2840 DL listed. Can you please help me get the right channel balance? Thanks Dan

I have 2 channel balances in need of replacement. The channel alone is 27" on one and the other is 9" and the channels are hemmed. I can't figure out the sash weight or what to order for the top and bottom. I see similar, but can't find that same top. Thank you in advance!

I need to order (2) new channel balances for my non-tilt vinyl window. The code on the original balances is BSI 24 DS 35 The brand of my window is Windowmaster. I have attached several photos of the end clips, which I cannot seem to match up the clip types shown on your website. Please advise ... (cont.)