Viewing all customer Discussions for:

15-004 Winged Channel Balance Shoe, 1-3/32" Depth

I sent a note yesterday regarding my need for a ballast for a Lawson window. I attached pictures and I am afraid the size might have been too big since after I hit the submit button the screen just went blank, no confirmation of sent. Can you let me know if you got my original request? Otherwis ... (cont.)

28" in length from tip to tip 1/2" width Markings: 26 4 FT CMC 4

I have a single pane vertical sliding window with broken balance. The window is about 22 lbs (weighed, not estimated), and 28" tall. The channel itself (the metal part) is 26" long. The window was made by Philips, as noted on the lock. From your catalog, I see that these could be either series 3 ... (cont.)

Information written on side of window balance: 33 3 CALDWELL JM It measures 33 3/4 inches in length It measures 1/2 inch in depth

Need help on the correct series to replace my Milgard Channel Balance, the code stamped on the original part is 32 5 CW CMC 8 The channel shoe measures 1 3/32" in height, the metal rail is 33" long and 1/2" width.

I need a 2 of these do the ends come on them or not or do I have to order separate I measure 30in with the plastic tips but 29in just metal I also need the little prices on inside of of sides of window can u help

Need spring assembly pulley hardware for a 900 series single hung fin or flange frame window manufactured by NuAir (out of business) Tip to tip measurement of spring assembly including plastic is 36" metal to metal = 35" The window sash measures 36x48 and weighs 23 lbs. 1/2 inch channel Str ... (cont.)

Hi, Just need to confirm which replacement balances to order. I've attached photos of my existing balance. Measured length is 28" metal-metal. Not sure which model best matches my plastic ends. I need two balances and 10 take out clips - item 16-002. Thanks, Paul

I have a window with 2x broken Unique re-tractors. The Item is marked 22-D-40 UNDER THAT IS 02/05/S7....NOT SURE ABOUT THE S Keith

I am trying to order 4 Balancer for my 2 sets of window. Length of channel itself is 29" and overall section including both ends hardware is 30" and width is about 9/16 of an inch. ID number on the channel is 2820G.

I'm looking to repair/replace a window balance in one of our windows. Part of the block and tackle pulley broke. I've included a link to photo's of the part that needs replacement.

Hello. I have a Milgard channel balance that I need to replace. The stamp option on it has a few other notations in it - see photo, so I'm not sure if it just works out to 2640 or if it's something special. The window is probably 30" x 36", unknown weight. Additionally, the channel height is 26 ... (cont.)

Hello. I need to replace at at least one window channel balance of a pair, ideally both. The stamp on the side of one of the two units reads: 29 9 CX CMC 4. They measure 30" long and 1/4' wide. I've included 3 photos of each end of the units, including one that shows the problem on the one that eith ... (cont.)

This is from a Kinco Window. I believe it's 35".

I need a couple of replacement channel balances and want to find the appropriate matching part and get a price. The stamped numbers/letters, which don't seem to correspond to your system, are: 26 9 KV CMC 2. The window (lower sash, metal frame, double glazed) is approx. 46" wide x 29" high x 1-5/16" ... (cont.)

Hello, I'm trying to find a replacement for the window channel balance with the following descriptions: + Non-tilt + 1/2" width + 27" length + Images attached Thank you

Hi My window balance broke after many years of usage. It is Caldwell brand with imprint on left one: 27 4 EP Caldwell right one: 2740 B SI Please help me find the right replacement Thanks Michelle

Hi there, I have a few windows made by Phillips Stayton with the balancers brocken. THe blancer code as you can see in the picture is 26 9 but I doubt there are correctly choosen. Please recommend the corect spring tension for the 35Lb sashes. I want to mention also that the window is very thic ... (cont.)

I am trying to determine what balance that I need to buy. The attached pictures are of the top and bottom pieces. The Bar is 30 inches long and is stamped with 2950. I am confused as to top and bottom attachment I need. I need the complete channel balance with attached parts so could you pleas ... (cont.)

Hi, I am looking for replacement channel balances for Pacific Windows Corp Vinyl (non tilt) windows. The channel balance cover is 30" in length and 1/2' in width. The marking on the balance cover says: "29 3 B SI". See attached pics for shoe and top styles--front and back. I would like the comple ... (cont.)