Viewing all customer Discussions for:

15-005 Winged Channel Balance Shoe, 1" Depth

I found that one of my balances had fallen out. I then looked up online on how to remove it in the hopes of installing it in correctly again. However, I found that a few of the plastic pulley wheels in the balance assembly and a plastic bracket/stopper thing that was screwed into the window frame ha ... (cont.)

I'm tring to find the repalacement part for a bsi 2730W. It looks like it is one one the foolwing but I can not tell what the difference are. The top and bottom shoes look like one of the following: 350, 380, or a 385 The length of the steel channel is 28". Width 9/16". Depth 5/8" ... (cont.)

I have a block and tackle balance that busted. I made some repairs and it worked for a few months. I do not know the window manufacturer. The only label on the window is the AAMA cert sticker. Is the balance I have one of yours? If yes, where can I get some (if one goes, others will go)? Bill ... (cont.)

it appears I need to replace the window balance since the plastic centering pulley the cord runs on has broken and it doesn't appear that it can be replaced as a separate piece. I have Kinco windows in our mobile home and as far a a part number for this part, the only thing I see is #26 3. The met ... (cont.)

I need to replace some window balances which appear to be series 380 (w/#19-005 bottom clip) or 385 (w/#19-004 bottom clip) but your website depicts these clips identically. How do I determine the correct clip? Inside dimension of my channel is 1/2", wing to wing width of clip is 15/16" and heigh ... (cont.)

the stamp on the balance reads 31 5 EQ Caldwell and it is 32 inches long which channel balance and ends do i need

I have a couple of window balances to replace. The metal portion is 21 inches long, not including the plastic ends. The metal portion is 0.5" wide by 0.625" deep. The stamp reads "20 5 IW CMC 7". It is for a Milgard, single hung, non-tilt window. The portion of the window that it lifts weigh ... (cont.)

Hi I'm looking for parts for my windows. I have some numbers and images. Here is the number from window H-R20-48-72 and numbers from part 26 5 ER caldwell. I believe this part call channel balancer system left and right. I need for 4 windows . 4 left and 4 right. I will appreciate if you can let ... (cont.)

I need help in identifying the right part to order. I need to replace 2 window balances. The length of my current one is 34 inches. the window weighs 23 pounds. It appears that the product that looks closest to what I already have is the 34" Series 380. Thank you.

Hi, I have a 15 inch channel balance which needs to be replaced (stamped 14 5). I measured the shoe and it is a 15-004, which corresponds to your series 385 balance based on my balance top. When I looked at your options for the series 385 however, I cannot find the 1450 option. Can you sug ... (cont.)

Hi, Our (first) channel balance has broken. We think the original window was a Milgard. The number stamped on it is 25 4 BV CMC 1. The shoe depth is 1". Which of your channel balances should we be looking at? Thanks much.

I just replaced my channel balances in a non-tilt window. I ordered the parts based on the stamped number. The window now makes a zippered spring metal noise when I open or close the window. What is going on?

The existing channel says the following- 33 5 cq caldwell However, I was told at the local hardware store that I needed a 34" and also needed to know the weight of the window which is approx 37 lbs.

Can you tell me what the difference is between the 380 and the 385 series? I see the shoe has different numbers but they look the same in the picture. Mine are stamped 1720 and are 17 3/4" long. I need 4 of them. Thank you, Bill.

The 1/2" Channel Balance looks like a 380 or 385. The top guide is certain, but the bottom guide doesn't look like either. The metal part is stamped with B.S.I. and 1010; it is 11" long. The window is 25 years old. I ordered this same part from you a number of years ago, both for this window ... (cont.)

Hello, I need to order the correct channel balance. This is 1/2 width, and 36 inch long. on the balance it self it has the 34 4 K CALDWELL Mark. Looks to be the 36" 380 Channel balance but i cant find the 344 option. Please let me know what I should order, here are some pictures

believe I have a 33" 380 series. Faint tamp of 32-2 BSI. See enclosed pics.

Hello, the top guide of the window sash broke and I may need new channel balances. I identified your 30" series 380 with option 2930 BSI(stamped on the original channel). however, the bottom attachment (winged) is NOT 1" as your 15-005, but only 7/8". can I use your 15-005? Thank you, ... (cont.)

I am having trouble finding an exact replacement for the support channel balances. I will attach some pictures of the ends and maybe you can give me the correct parts #. The rods are 1/2" X 31" and are stamped 3030. Thank You

I'd like to correctly identify the replacement window channel balance. Attached are pictures of the broken part I need to replace. 9/16 channel width, 30 inch length It seems to me Series 380 or 385 should work, but would like to make sure. Thanks. Peter H.