Viewing all customer Discussions for:

36-090-10 10" Stainless Steel Egress Snap-on Hinge Set

I have a case met window and when it's open the edge of the window is part way into the frame opening. Which makes it void as in egress window? I need to change the hardware on it so that it opens on the exact edge of the frame and does not block any of the opening. I was told you can help me get t ... (cont.)

Hello per your request these are the pictures of the current mechanism. I am looking for something that would allow the window to open fully so I have 20" clearance. Thank you.

The black piece on the right side is split in two. It's supposed to hold an arm in place while it slides on the track. Can i finf the black plastic piece by itself or do I need the whole track? I can go either way.The black piece is broken in two. It's the piece that slides in the track. ... (cont.)

I need to order all the parts from the attached pictures.

This operator is from a Wilmar casement window /stamped Truth. U.S. Pat 4,241,541. The long arm is stamped 30472RH. The short arm is stamped 30850. Thank you for your help.Best Regards,Evan

Hi,I am hoping you can help me. I have a Crestline crank-out window from about 1992. When I am inside, it is on the right side. So, from what I read, I guess I need a left-side thingy! Anyway, the window will no longer open. The crank just goes around and around. I switched handles, but that did not ... (cont.)

Hello,I have a certainteed casement window originally installed in my house 2004. I recently finished my basement and the inspector says this window doesn't meet bedroom egress as the opening is only 15.25 inches. Do you sell any hardware that would move the casement panel pivot point? Moving the ... (cont.)

I have many Vetter Casement Windows with Truth Entryguard hinges. I would like to replace the upper/lower sliding hinges, and the crank operator and arms for a window that is hinged on the right when looking at it from inside the house. The pictures and part numbers referenced herein are for a win ... (cont.)

I have a jeldwen window that is 32 x 48 high tip to tip the interior of the frame is exactly 24 inches so when the sash opens it opens about 4 inches into the window opening not allowing it to pass egress code

Looking for Windsor Egress hinge arm operators, their part numbers 540019 and 540020, one pair both right and left. Also need one of the posts that screws onto the bottom of the window that the short arm of the operator slips over and clips onto. Need the one for the left window looking out, or the ... (cont.)

Hi, I need your help in identifying the proper replacement hinge for my casement windows. I believe that these are Truth egress hinges that allow the window to open 90 degrees. They are 24 years old and one of the window hinges has failed. I looked on your site and can't find anything close to what ... (cont.)

We have 4ea 20 15/16" x 56 1/16" Casement windows assigned as egress. However, the hinges provided with the window limit the emergency egress by 3". Please advise a hinge replacement to allow the window to open 20".

I am inquiring about changing the hinge/ pivot point to allow the window opening to be larger. Bishop

Will this work on above mentioned casement to widen the opening and keep the window closer to the frame? Thanks Roger

I need new hinges. Based on the picture which hinge do you recommend? 36-004-10 or 36-048. What is the difference?

Hi I have recently Purchased multiple replacement parts for these windows but for some reaseon cant find the hinge sets I need..I saw a article that had the exact same window as I have and you recommended buying this hinge #36-004-14 14" steel 2 Bar hinge set but it wont work with what i have.. belo ... (cont.)

Good morning, I am in need of egress hardware for this Paradigm casement window.The window was purchased last year and is a Paradigm 8300 series casement window.The dimensions are 29.5" x 41.5" although the sash meets egress requirements the sash swings into the opening and causes the opening to be ... (cont.)

And I have a Silverline casement window 70NCW1?.. has it is installed now, I have 5.189 ft.² of clear open space. I need at least 5.7 ft.². I need to acquire whatever hardware is necessary to make the window open further. Please see the pictures attached.

Number on hardware cw35-cw6 and below that cxw5-cxw6 23 " str can you help replace hardware and hinges thanks ?