Viewing all customer Discussions for:

15-015 Pivot Shoe, 17/32" Thick

Good Morning, Please find attached pictures for the original window spiral balance. Please help me to identify what is the part number I should order from you. I have four windows need to replace the spiral balance. The tube length is 29" and 5/8" diameter. I would appreciate it if you could ... (cont.)

Trying to repair my Mom's window. I had my wife send you a few pictures of the parts that I need to complete job. series is nc 1500/1600, I have more info off window tag if you need it. I think I need the pivot shoe 15-046, but part 15-015 looks close also. The spiral balance seems to be good, b ... (cont.)

This is a spiral balance system. I need to replace these parts/

I am looking for Window parts, I have about 20 window, some will need latches, pins on the bottom of the windows, tension springs and attachment bracket, I will also need the tools to set the tension on the spring.

I have several pivot boots that have broken and need replaced. My sashes say Traco-1-77 inside of them. The pivot boot is a white/cream color. It is 1 1/4 inch wide, 2 inches tall, and about 1/2 inch thick. It has Patent 3,055,062 stamped on it with a 3 above that. No other distinguishing marks. Tha ... (cont.)

In trying to insert the window pivot bar into the Pivot shoe I place the sash into the shoe slot as shown in the video. However, the bar is only aligned with the shoe slot when the window is straight up. This position will not allow the window to be tilted sideways to insert on bar then the other. ... (cont.)

Sir/Madam Can you identify attached Pivot Shoe for Spiral Balance. It is two inches long One and quarter inches wide and half an inch thick (deep) If so can you supply them. Thank you PJ

d

This is a 23" window balance with no names, numbers or markings. The top of the balance was secured by a single screw through the cylinder itself. Any help is appreciated

Good day, we have purchased a house that has a large number of older vinyl windows. In general they seem to be OK, but many have stuck or unsupported sashes. The pictures show a pivot shoe that consists of two components. The longer piece is broken off at the top. The round piece turns inside t ... (cont.)

dimensions: 9/16" thick X 1 1/4" wide X 2" long This is for an all aluminum doable hung tilt windows Need 12 of them.

2" long, 1 1/4" wide, and 17/32" thick. I'm assuming either the 15-015 or the 15-046 would work. Any advice on which one? Thanks, Bob

I have three vinyl replacement windows in the living with the same problem: none of the sashes will stay up. I've been doing some research on your site and am hoping to repair them myself rather than replace the windows. I've removed one window so far and found they are spring balance, but all th ... (cont.)

Shoe: w 1&1/4", h 1&15/16, d17/32 Sash lock: w 3", h 3/16", d 5/16 I have been told that they are keller windows thank you very much for your help 800 574 - PAT. 3,055,062

Sir Can you identify the model number of this window I am trying to find parts for, the lock and the lower right hand corner of the glass say Alcoa? The window measures 22 wide x 57 tall, they are tilt out style? Thanks

I have a client with Acorn slide up windows and need replacement parts for same. I have attached pictures of the tilt out side rod mechanisms and I see on you web page similar rod mechanisms but no similar nylon bottom pieces that the pivot pins on the window can fit into. The rods measure 29" an ... (cont.)

shoes look like 15-015 sometimes break after year or two at thin side. 1. how prevent/postpone break? 2. 15-046 fit? last longer?

I am locking for a Window Pivot Lock Shoe, for a "Home Window Co." window. It is made of aluminum. It's a very old wiindow I'd say 1970s or 80s. the tag says the company was from Fostoria Ohio. by your pictures and measurements It looks a lot like it a Swisco window part. I've included an image of ... (cont.)

I am looking for a guidespring that goes into a pivot lock shoe This is for a 3 rivers dbl hung tilt out window

I ordered the 15-015 balance block for my aluminum track windows based on the color (blue). They don't fit so I have now ordered four 15-046 (beige). The 15-015 could be forced into place with a rubber mallet but is too tight to move up or down. I will need to break it out with pliers or sc ... (cont.)