Viewing all customer Discussions for:

39-014 Casement Window Operator, 13-1/2" Arm

Window crank. 40056

Hello, I need to get 2 of the 45135 left hand cranks, and one of the 45136 right hand cranks. both of the 45135 cranks have 40051 arms, which have a 12 inch straight before a 2 inch straight after about a 135°. The right hand is the same except it is flipped and unfortunately the number is worn off ... (cont.)

Good morning! I need to locate the parts to repair a window that was installed a few years ago that did not have the tracks installed on it for the operators. The daylight on each is 18" for the glass, the casements are around 22" each which give it around a 48" outside to outside of the window. ... (cont.)

Looking for replacement for this operator, the best i can gather a discontinued truth operator. will appreciate the help. Also need second one with opposite direction for the other window. Thanks!

Can you identify these cranks? They look like the Caradco 39028 on your site, except that the crank arm is longer. The 9 1/2" measurement on your site looks to be 11 1/2" on my mechanism. One of the attached pictures shows the crank mechanism wit a tape measure to show relevant measurements.Thank ... (cont.)

I have 2 casement windows with cranks that won't close all the way - 1 is right handed and 1 is left handed. I think the gears are stripped. The long arm measures approximately 13 inches. Do you have replacement parts - I think I need complete package - crank, cover and screws as well as arms. ... (cont.)

Hello, We need help deciding on which parts to get to replace the the entire crank mechanism (hinge arms, track, operator) on our 1980's Hurd double casement windows (left and right). Could someone help with this? Double casement widow width each 17.5" Hurd windows House built in 1982-4 Thank yo ... (cont.)

Needing parts for casement windows. 1. Track/pivot- the track the window travels on and has a pin for the pivot arm. # on it is 358-1L. The one shown is the right side opposite of the one I need. Also need a locking arm for the lock shown. Not sure on make of windows but house was built early 80s. P ... (cont.)

Can you help us find the correct replacement? What else would you need to know?

Hi this piece won't crank. I push it up and it kinda pulls it back in but not all the time. We are selling and trying to figure out which part it may be

I am looking to find replacement or very similar versions of this part. It is one solid piece.

I need a new Hurd window crank. It does not crank out or back in. The handle just circles with no connection to the window as it just swings out after unlocked. We have to push it back from the outside to close it. What part do I need? Thank you!

Hi the part I'm looking for is a Truth window operator with single arm. Based on markings it appears to be # 45107 RH.

Looking to replace this crank mechanism for our windows. Can you help me identify it? I have some that need to be replaced that are left hand and some that are right hand.

Does this come in white and can it be removed without damaging the wood frame? Left and right handed?

Hello - I need ALL new hardware (every metal part) for approx 16 of the wood trimmed windows and for 4 of the painted trim windows. We have not closed on the house so I cannot take anything apart at this time. I want to confirm that you have all the hardware I would need to complete this project - I ... (cont.)

truth 45251 operator arm

Hi, Can the swing arm be replaced? The window was forced open and the arm was bad. I haven't been able to find the same style operator online so hopefully you can help. The swing arm has Truth stamped on there and it's about 13" long. Window swing out from left that makes this a left hand operator? ... (cont.)

This operator is on a weathershield casement window, about 45 years old. The arm has the name "truth" on it and the crank handle is not removable. I need replacement hardware. Thank you

I am in need of this type of opener. The operating arm is stamped "Wright" & is approximately 14 inches long. Other information is also pictured in the other attachments; 358-1L & 30382- 358-1R.I am also in need of upper and lower hinge assemblies, if those parts can be suggested by these p ... (cont.)