Viewing all customer Discussions for:

39-061 Keller Window Crank

Which part would be best to replace this part?

I'm trying to identify which operator I need to buy. The hole for the operator arm is threaded, but I don't know what type of threading it uses. I also don't have the name for the window manufacturer as they are all illegible now. The house was built in 1966, and the identifying markings are long si ... (cont.)

Need three right operators and one left operator for 45 year old windows. Want to buy one right initially to ensure fit and function. Arm length is 2-3/8" - not sure about thread dimension. C-C vertical length is 5-1/4". If colors are available, white is preferred. Only information on existing close ... (cont.)

I can see some numbers 11500-4

I have been unable to match this opener, attaching pictures. House was built in 1955 and has original windows. Thanks

I wanted to know if you knew a replacement part for this hand crank. There are no names or numbers on the windows or cranks that I saw. Thank you for your help.

Hi, I have several of these window cranks that are not working properly on a three season porch... Can you assist me in identifying the model number so that I order the correct one? Thank you so much sincerely.

SD only marking It's a right hand operator

Window doesn't close completely please attached picturesThe part appears to be 2" x 5 7/8". Approximately if you don't feel the operator is the issue please make recommendations. ThanksGavin.

Good morning, this is a crank for a triple window operator crank. I measured to the best of my ability, so I'm going to say this is close, but not perfect. I have 4 cranks not working...I have 9 of these windows. Top hole to bottom hole: 5 1/16 Top hole is a single hole Distance between bottom 2 ... (cont.)

my operator's dimensions resemble all of the specs you show on your 39-025, with one exception. My operator doesn't have that sharp offset in the inner arm. Would that make a difference?

I would like to replace three easement window hardware in brown. The windows were part of a Four Season Sunroom. The body measures five inches and screw holes are 5.5 " apart.Please identify this part so I may place an orderThank you,Morris

What's a post? The crank has one hole at the top and two at the bottom. From top to bottom the distance is 5.25" measuring from center of hole to center of hole. The distance between the two bottom holes is 1 1/8". The armature screw is i/4" long (just the threaded part) and 3/16" thick. I sent a ... (cont.)

The units have right and left side cranks the spread from top screw to bottom screws is 4-3/4" center to center the windows were from the late 1950's. Are any of your products a match?Thank you,Frank

Hello. Please help me ID the window operator and cover plate for my windows, images attached. Arm extension measures 2 3/8". Also, operator mounting hole needs to be to the right at the top, not centered. Thank you.

Don't know the maker and there are no markings on the cranks.

Because I repair my own awning windows, a friend asked for help on theirs.I have not found any identifying information on the window or operator. She has a whole houseful of these. The pattern on the operator housing is unlike any that I find online. If you need any further details, please let me ... (cont.)

Hi all, Hoping to confirm a part number for 6 left hand replacements. Hole spacing is 1 1/8 x 5.25 with a 2 3/8 arm. Some of the arm attachments seem to be via c-clip and others by threaded grommet. Also looking for an extended or straight crank handle. One was installed in a corner beside a door ... (cont.)

The arm measurement is 2 5/16 and the screw hole is 3/16 threaded The distance from top to bottom hole on center is 5 1/4 Distance between bottom 2 holes on center is 1 1/8

Hello My name is Ken I need both LH & RH vertical rollera. Isee no name or numbers on window or rollers, but here are the measurements. The roller has 1 hole in the top-- two holes in the bottom.Overall length-5-3/4in . width-2in.c-c top hole -bottom hole-5-1/4 in, ( not aligned) c-c bottom hol ... (cont.)