Viewing all customer Discussions for:

Door & Window

Older home, custom size screen door. The latch parts are 1/4" or less wide for aluminum channels. The part in the photo is cast with 7027 part number. I ordered and received part 91-176. The parts are too thick to push into the channels.

Need a replacement latch for a Pella retractable screen. Refer to the attached photo

I need to confirm what I need to replace old sliding glass door inset and if a handle can be added.

Length - 26.5" Stamped - 26 4 Count - 2x

These are plastic clips on the bottom of my screens for removal. Because they are plastic they break easily. If there isn't something like this available, maybe a retro fit part. Something that will screw into the existing hole and help with removal of screen.

Any help identifying the roller assembly is greatly appreciated. Trying to update/replace to improve open/close resistance.

I need this guide and instructions on how to install it. It keeps letting the bottom corner go out and when you close it it stays out unless you have someone on the outside to push it in .I would appericate your help.

Patio door and screen have no markings to manufacturer visible. Pictures are of a top and bottom assembly. Parts look identical other than the addition of a spring on the top unit. No identifiable markings on the wheel assemblies.

From '94 in eastern Mass. The part which attaches to the bottom corner of the window pane, and slides side to side, is rusted/corroded on several windows. This has caused them to want to be stuck in the open position. And to close them for now I need to push in from the outside while someone else cr ... (cont.)

I would like to replace these shoes. They are difficult to figure out where to press open or close. My window reads 20R. Please suggest which shoe would work best for me.

I ordered a multi-point mortise lock replacement for my patio door, and I can confirm that it is the exact same lock as my former one (both have Patent #'s 5.264.252 and 5.820.170 engraved on them. The old lock was manufactured in Sep 2008, and the new one was manufactured in Jul 2021 (A1). I have ... (cont.)

We have a pair of 25" W x 50" H casement windows where the right side window crank is too worn to open and close the window. The crank handle easier comes off. You can see the gears have worn out. The arm extending out from the mechanism is at least 12" long. We are looking to order the correct rep ... (cont.)

I have two broken coil balances in each of two window frames, and I need a little guidance on selecting and installing replacement parts. The windows both weigh 16 pounds, one is 25" tall and the other 28". The top part says #9.0. The springs and snapped down to the shoes, and they read #9.0 and 35" ... (cont.)

Need 2 replacement parts for 32-5 KL5 CMC 3 or 32-5 balances with wing tabs. Please quote for (2X) balances.Also, I was trying to look into your website for refereces. Is 33" Series 385 Channel Balance #S385-33 a comparable replacement with winged tabs? Please advise.Thank you,RP ... (cont.)

Single arm, RH (crank on the left side). The word "Truth" and number 40065 on the underside of body.

Need help identifying correct replacement. The lock has broken

Hello,I'm looking to purchase several sets of balances for my windows but want to make sure the measurements are correct. I have them at 34.75inch tall balances to the top of the plastic tubes which looks different than the balances in your videos. Please see attached pictures. It makes me unsure of ... (cont.)

Do you have the piece to fix my Pella screens that are broke on all corners?

One is shorter than the other

Working on some windows and unable to find the match on the website as the part that I thought was it, only goes up to 26 stamp as mine is a 30 stamp. I think I need a triple coil. I have attached a picture for reference. Is this something you have in stock? If so, can you direct me to the correct l ... (cont.)