Viewing all customer Discussions for:

Door & Window

I need a replacement storm door handle for Idea DX-1C in white. The storm door was purchased new in 2004. Do you have a replacement or know where I can get one?

Thanks for looking! The bracket is 1.5 " long 7/16" tall and wide The wheel is 1/2" dia with a 4/16 hole The axle is 1/2" long and 3/16" dia I found no labels,stickers or stamps on ant part of these windows The complex was built in the early 80s Jeff

Hello, I've attached three photos of screens from my 1974 vintage Anderson casement windows. The screen is held in place with metal spline. The width of the frames, both the same for both sizes of screens, is 0.75 inches. What size foam or plastic spline do you recommend if I am installing fiberglas ... (cont.)

We cannot get the sliding Dorwal 1200 door out because of inside tile higher than the bottom slide bar; how does one remove the stable door so that we can then remove the sliding door towards the outside rather than the inside of the house. Thanks. (I recently bought several new rollers 81-030 for y ... (cont.)

Hi , We would like to replace the rollers only with nylon rollers. The existing rollers are brass with a fixed axle that fits inside of a stainless steel housing. We have a bunch of doors. I would imagine we will need at least 50 rollers. We will get an exact count of course. The owner likes ... (cont.)

The Pivot Bars I need look almost identical to your Product Code 26-360 except that they are 2-15/32" in length and have two holes centered 1" apart with the first hole located 1-7/16" from the head (opposite the pointed side). I do not know the name brand of the window though I think it was a milg ... (cont.)

Hello......... My order arrived in good time and in good condition so no problem there. However...... in attempting to install the unit I see there is a major fit problem in that the new unit does not match the original Caradco lower window wood trim cutout. This unit has a different lever enclosu ... (cont.)

Marking on it is 25 5 IO CALDWELL, if you need more let me know. Don C

My sash balance is marked 11600-2, I don't see a replacement part. These windows were made in 1981. The top sash is 20in., bottom sash is 19in. The cord is approx. 25in. Can you please help? I found another number - "J70 5423 9-81" The sash is about 27 7/8in. wide. The previous measurements of ... (cont.)

I have a casement window that I am trying to find a replacement for the crank system. Listed below are pictures that might help you locate the type of system that I have. Thank you, Gary

Please see pictures of the assembly needed.

Please let me know pricing. If possible would you have the manufacturer and model number of the balance? Thank you very much. Steve

My windows are Weathercraft series 3000 vinyl tip in, first pic shows what it SHOULD look like..the others are the actual top and bottom pieces as well as the balance itself. It is 1/2" wide. No markings avaialble..once removed I cannot replace the window. House is on the market for sale-for securit ... (cont.)

I am looking for two replacement latches for a Traco 1GCC CBA 87 window. Thats the only identifying number I can find on the window. Both latches have broke at the plastic slide piece which holds the top in the frame.

hello..i have identified the rollers for my aluminum doors. part 84.010 looks to be exact with the nylon roller 15/16 wide. the 84.071 looks exactly the same except for the metal ball bearing wheel which would be a lot smoother but has a 1 inch wheel. do you think it would fit? the doors are doors b ... (cont.)

Hi, I believe my 2-panel Andersen patio slider was installed in the late '90s. The thumb lever is broken. The screw holes measure what looks like 2 17/32", or very close to it. The color is like clay, possibly stone? Is the 82-043 the correct part to use? Thanks!

Sir, At first I would ask if the 1st two images are sash guider, as I did not see any similar part in your web? The top and shoe are showed in other images. The stamp is "19 B", following "BS.I" which is in a vertical direction. Could you please identify the replace parts from you? Who is orig ... (cont.)

Hello: My operator seems identical to the 39-035 except it doesn't have a hinged arm. My arm is about 8" long tip to pivot point on the gear. Questions: 1. Do you have a 39-035 operator with a straight arm? If yes, price and delivery? 2. The gear seems to cover the mounting screw hole howeve ... (cont.)

Chain and window are fine but the gear section needs to be replaced. Can you help? PATENT NO 4,505,601 4,521,993 PAT. CANADA 1986 U.K. PAT. 2,135,397 TRUTH 45015