Viewing all customer Discussions for:

Door & Window

I'm looking for the coil balance that would go with Coil Bushing 15-143 and Coil Bushing Cap 15-144. I see it says Use with Series 150 and Series 152 coil springs, however those coil springs don't match up to what our customer has. I've attached several pictures that will hopefully help with ident ... (cont.)

I ordered 2, 23-070 roller assemblies. They are exactly what I need other than the roller itself. I need a "male" roller as opposed to a "female" or grooved roller. I can't find it anywhere on the website. Help.

I need to purchase channel balance for NuPrime Seasonall non-tilt window. The length of the channel from one end to the other, not including the top attachment and bottom shoe, is 28.5 inches with marking 2820. The one closest product is S390-29 based on measurements of the shoe. Attached are ... (cont.)

I don't see the right 'Top' or 'Shoe' in your parts list. The spring actually hooks into the plastic Top and the Shoe is part of the block & tackle, the # stamped is 2640. (Please see the pic's I sent)

Casement Window Crank - Roto-Gear Operator and Lock Detroit Hardware No. 2320 L-H

Alenco is the name on the window lock. Channel measures 9/16" so would be considered a 1/2". Length of metal channel is 28 1/16". Stamped on the metal is the number 270. I'm not sure if I've used the correct angles to take the pics of the parts from for identification purposes. Please let me know an ... (cont.)

Hi Susan, When we spoke the other day, you suggested that I send you a picture of the wood casement crank mechanism (rather than sending it on to you) that I am trying to replace. If I can't get an entire new one (or several), I could use some handles. Here are some specs: 1) The leng ... (cont.)

I have a 28" channel balance from an old SunAir window. . It is stamped 2720F. What would I purchase to replace this? Also all of the windows we have of this type don't have take out clips,but the frames have a space for them. Should we order them as well? Thanks!

there is a 2740d marking on 1 end. The balance is 28" long. It appears that S350-28 is the correct slide. 28" I included pictures and wanted to verify that it is compatible. I need 16 slides, but do not want to pay $12 to test 1 slide, when shipping for all 16 is around $23 Thanks. ... (cont.)

Hi - I have a non-tilt Fiberlux window that does not stay up. I have pictures and measurements of the channel balance as follows 1/2" wide - 22" long - Item No. 21 3 or C (not sure - pls see picture below) I have seen many videos, but there isn't one out there that shows how to replace the ... (cont.)

Hi I have never installed one of these cranks before: I bought the replacement part(s) from Home Depot, and was advised I might find "how to install" instructions on-line. Can you please provide a link? Or better yet: easy instructions. The window is on an upper floor requiring a very tall lad ... (cont.)

the metal part of the balance is 27" long, 1/2 " wide,it has the markings 2640E (the E is backwards as shown in the picture)and the small letters B.S.I.. and in handwriting milgard 2640

I have confidently found rails for one room as per this page: http:/. ww.swisco.com/28-inch/pd/Series-351-Channel-Balances/S351-28 the stamp matches up. The other room is the same style except longer. The stamp however reads 33ds ea 42 as per attached picture. It wofactappear I need the 351 ... (cont.)

Andersen number L1427/45 or part number 9013991. What is your equivalent number?

I need parts from what I am told is a Patriot window, 20 years old: 1) The tilt latches. 2) The pivot bar. This is riveted with one rivet. The protruding area looks like a "u" channel. 3) Perhaps, the balances. They are cracked at the bottom but to work. Thank you.

We are trying to find the right replacement balance box for Anderson Narrow Line windows. The glass on the double hung window measures 28" x 56". We've taken out the top guard piece to reveal the original balance boxes. Unfortunately the numbers printed on these boxes are very hard to read. There is ... (cont.)

Attached is a photo of the existing broken latch. It is 2.5 inches wide and 3.5 inches tall. The screw holes are set 3 inches apart. Do you have that type of latch? Ellyce

I need some help. If you give some guidance as to what part numbers I need for my Anderson windows. I have 6 windows that lower sash measure 28 1/2 inches wide and 23 and 7/8 inches high. I also have one that is 32 inches wide and 15 inches high. I would like to replace the balancers but do not k ... (cont.)

We had casement windows installed sometime around 2001. I don't recall if they are Marvin or Anderson windows. Somehow we lost two of the operator covers and never made the effort to get replacements. Picture enclosed of both crank without and with the cover. The opening is 5 1/4" x 1", and the ... (cont.)