Viewing all customer Discussions for:

Door & Window

Attached is my part that the teeth on gear is shot.. I have a 9" arm with 3 1/4" hole spacing on body for screws. I am trying to confirm that your replacement part is Fenestra, Casement Operator, 9" Product Code: 39-358 If not can you guide me? If so, Does your part say "Fenestra Detroit " on ... (cont.)

My channel balance has the numbers 38 and 2990 stamped on it which I don't see on your list. It is 1/2" x 30". The window measures 50" wide and 30 1/2" tall. What balances should I order?

I took some pictures of my problem windows. Things I know for sure- American Craftsman Circa 2001 or early 2002 When some cleaning people were washing the windows they inadvertently made them crooked and the hinge snapped. This is the bathroom window. Jennifer

Looking to find replacement for sliding window. It opens horizontal. Its plastic.

Looking for compatible replacement for Channel Balance: 26 5 FW CMC 0 ,(window manufacturer unknown.) Length 27" x Width 1/2" x Depth 9/16".

Hello Friends: I have rusty Andersen Window knife latches that I would like to replace. How can I pull them out without ruining the frame?

Series mark 40/50 HP H-LC35-53x96 H-LC50*-53x63

Hello, I am looking for replacement sash Balance for 2 Vinyl NON tilt windows. the current balance are 28inches X 1/2inch wide. The only marking reads: "27 14L ok BSI" Could you suggest a replacement part? Thank you, Igor

need replacement part for 12 year old window these are the markings on the window HLC35* 114x87 40-50-shwb thanks!

I'm looking for replacements for my casement operators. The part # on the bottom is C-1040-9A. The outer arm has a sliding clip. The outer are attaches to the under side of the window. There is a triangular logo on the mechanism. It might be the letter "A" w/ a double underline. Distance betwe ... (cont.)

How would I replace this window controller, mobile home josley window? How to you remove it from the metal bar? I believe it is a Phillips widow controller..........

Hey customer service, Here's the image of my old broken shoe clip. That i'd need a part no. ? -Tien

Pleas help identify this part.

Our sliding door is difficult to close from the outside because it only has a flush mount handle. It is a DNS with a screw hole spacing of 6-9/16". Ideally I would just like an inexpensive outside handle. I have pictures but I cannot paste them in your message. Cheers Nick

I need to replace my closet door hangers (son lost the hardware when he removed the doors 3 years ago-love him!). What is the importance of the offset? Thankfully you have the 3/4" wheels, but I can't decide on the offset. What difference will it make? There are 2 sliding doors on the closet and the ... (cont.)

I am looking for the right side pivot pins for a vinyl top sash of a double hung window. There off set so there should be a left and a right. I beleave the manufacture is Certaweld. Theres a number on the pin but i cant make it out it looks like it says 102-a or like a backwards capital B. Enclosed ... (cont.)

I have an Andersen sliding patio door that i want to install a key lock on. The door, from the outside, opens to the right. Do I need a 82-317 or 82-316? Frank

Hello, we are trying to fix what is wrong with our windows and it starts with the window cranks. I have included 4 pictures showing the crank handle (number inside handle is OP05-7810), the crank posts (with numbers HG04, 2004U and 052020) and the crank housing. I don't think I need to replace any ... (cont.)

Exterior and interior door pulls. Locking mechanism ok. Scott

Due to rust and wear, I need to replace the track on both of my 5 foot sliders as well as the 8 casters on the bottom of the doors. I have sent you two pictures of the slider as well as the caster still mounted on the door. I am not too sure how to remove the casters from the door since no screws ... (cont.)