Viewing all customer Discussions for:

Door & Window

dimension of bolt pattern to window frame 5-1/4 inches on center. width between screws top and bottom 7/16 inches on center (4 in all 2 bottom 2 top). overall length of link arm 3-1/4 inches (hole to hole 2-9/16). diameter of hole at end of link arm 3/8 inches, link arm is offset. need new ope ... (cont.)

I have a kinko patio door that I need to replace the locking unit. It is a flush mount and is the Mark V series. I would like to replace the whole unit and the part on the wall frame that the locks inserts into. I have attached a copy of the demisishions as close as I can get. Thank you Kathy ... (cont.)

No markings or numbers on part. Overall length 29 inches. Spring length 13 3/4 inches.

Can you let me know if your Mortise Lockset 40-049 is a replacement for the Emtek 322 lockset?

Do you have a guide on how to install this? I'm worried about cracking the plastic if I have to wrestle with it. THanks

metal measurement is 29" sash weight is 14 lbs not sure of top or shoe. There is a name --unique 28-B-20 on the side of the balance

Hi. Subject says it all -- the proper spiral balances arrived after order, but I'm clueless what screw to use to secure it to the window frame. (Original screw appears lost to the ages.) If you can give me the proper specifications, I can go to the local hardware store and get some. Thanks. -Gary ... (cont.)

I am replacing 28 inch spiral balancers that have yellow bushings, however, the weight of the sash is 16 pounds. Please tell me what colored bushing to order on the balancers. Also, I am replacing 28 inch spiral balancers on a 13 pound window sash. What colored bushings should I order for t ... (cont.)

Hello I have two different size channel balancers 15in. and 23in. 3/8 wide. The 23in. has numbers stamp on it but the 15in. does not. It is the S810 series. How do I place the order on the internet? I manage an apartment complex and will be ordering a dozen of each to start off with. Tha ... (cont.)

I have a home built by Adams Home Builders in 2002. I am having some problems with several of my Kinco aluminum framed windows. The nylon piece that is located on each side of the sliding window fails and allows the channel balance top to slide past. It always happens when I close the window. I beli ... (cont.)

I have searched your site and have been unable to find the correct replacement part for my windows. I have several of these pieces that have broken, and I am reluctant to open windows for fear of having more of them break. There are no markings to be found on the broken pieces, though the channel ba ... (cont.)

My windows are 20 year old Viking windows single hung. The number on the balances are (29")long #2840 with an upside down U at the end of the number. The next one (23") long with the #2280Y28. And a lot of the locks are breaking. do you have window locks. Looking at the pictures of the b ... (cont.)

Looking at back of unit is there a metal strip with groves that sits under top plastic bar , for support to hold coil sping in place? The units I have now are breaking at this spot , they do not have this metal strip . Could you send , better picture of shoe back Product # 15-140 pivot lock shoe? ... (cont.)

I need a side-mounted (vertical)screen pull to replace the plastic pull tabs that came with the Harvey windows.Can I mount your 70-204 vertically? I presume that pressure will keep it in place, right?

I do not need the screws that come with the 70-204 slip-on pull. Is the pull available without the screws? If yes, what's the part number and unit price?Thanks!

I would like to replace all the rollers on all of my screen doors - i have 7 screen doors that need to be replaced - they are all rusted and screen doors are getting tough to open and close properly

CertainTeed window Product Dev Double Hung

I'm trying to find a replacement crank. The internal parts are stripped. Would you have a replacement for this crank? Thanks, Shawn

looking for the rollers for my peachtree sliding screen door.the hole on top is the adjusting screw,one on bottom mounts the roller to the screen door.thanks guys

Looking for this identical lock and keeper set style, but *with* alignment lugs. Do you have this for an exact match or should I go with 90-177 and 90-077A instead? Thanks!