Viewing all customer Discussions for:

15-046 Pivot Shoe, 1/2" Thick

The balances I think I need to replace are 29" in length (tube only) and 3/8" in diameter. It appears they have black tips. The windows weigh about 26 pounds. Would like your advice on what replacements I need.

shoe measures 1 1/4 wide at top--2" tall---9/16" thick--- socket measures---3/8 wide---1/4" tall (opening)

First off thank you very much for providing this service of helping people identity window parts. Both this site and your youtube videos have helped me gain an understanding about all this. I have recently bough a house and unfortunately some windows have an issue with the pivot bars and locks s ... (cont.)

I purchased 26-369 but it is the wrong size. Original part is longer and has 3 holes equally spaced. Also has number 6240 stamped on it. Length is 3 1/8 inch. First hole is 1 5/8 inches from u shaped tip. 2nd hole used is 1 1/4 inch from 1st hole (middle hole not used). All other dimensions on the o ... (cont.)

Is replacing a pivot shoe in an aluminum frame the same procedure as your cut out video showing a vinyl frame pivot shoe replacement? My aluminum frames already have a cut out on one side in every frame. My concern is removing and replacing the shoe itself using the screw driver as shown in the vid ... (cont.)

Can please help me identify the correct replacement for this pivot shoe? Note the screw. The dimensions are approx 2 in x.75 in x.5 in. Measurements are approximate because part is still installed. No observable cut outs. If you need the part removed and then measured to correctly identify, please l ... (cont.)

Hi, I am looking for the replacement parts of my ALCOA windows which were installed in 1996. There are a couple problems with those windows. The white cases of the spiral balances are broken into pieces. So windows are hard to open. One window can not stay open. Some tilt latches are gone. ... (cont.)

Hi, I called your customer care office this afternoon about my windows missing pivot pin issue. Here is the background of my window. I moved in to my current house about 15 years ago. The manufacture of my window is Silver Lining. The windows are covered by 25 years warranty. But couple weeks ... (cont.)

Hi we are looking for these parts marked 530 for windows in our house Can you please advise Thank youKim

Looking for an identification on this. It does not look like the ones listed. There is a metal piece with hooks to go around the pin on these. The channel opening is roughly 1" to 1 1/4" wide and ~1/2" deep. THe sash is 20lbs and the end of the spiral tilt balance is blue.

It appears to be 9/16" thick, 1-1/4" wide and 2-1/8 tall I've attached pictures

The dimensions of this shoe are 2" x 1 1/4" x 1/2", as good as I can measure. It has a blue circle with an opening that is 11/16 x 12/16 with the peg being 1/16. The opening in the middle is 5/16 x 7/16. This is from a Traco double hung window that was purchased between 1995-1998. I would ... (cont.)

Hi trying to fix my windows. believe i need the 15-015 pivot. Would you agree. Also need some of the pivot arms, the spiral tool and the jamb spreader. Need 50 of the balance shoes. Thanks!

tilt windows were installed when house built about 15 years ago.Name unknown. I have replaced the upper window pivot bar with your model #26-412, with no problem. I now found that one of the lock shoe pivot is damaged & needs replacing. I was unable to disconnect the spiral balance from the shoe w ... (cont.)

I need to order six (6) of these shoes. But, I have no idea what the part number or description is. So, I'm attaching this picture in hopes that you can tell me, and that you have it. Thank you.

Thank you for trying to assist with this request. I'm trying to replace this piece in the photos below and would like to make sure I order all pieces needed. I'm also replacing the spiral balance and will order the following. Please let me know if I need any other parts. S600--32 balance me ... (cont.)

Spiral balance Pivot pin Constant force balance system

Hi I have trouble removing pivot shoe as shown in picture. The frame is steel, not vinyl. The right side overlaps the pivot shoe about 1-2mm. A cutout was already there from installers. I could not pry out with a screwdriver unless I totally break the shoe. Even if I did, I would not be able ... (cont.)

Enclosed is an image that shows the problem I am having with my window. I have a pair of single hung windows like the image on the left. They were put in by the developer of my 10-year-old condo and I do not know where they came from. There are no identifiers on the windows. One window works ... (cont.)

Don t know how to remove shoes from track. Need instructions as well as parts. I hope this is enough info. Contractor installed Windows. Home built in 1995.