Viewing all customer Discussions for:

16-023 Pan Am Take Out Clip

Do you have the plastic take out clips or can I use the metal replacement ones ??? Photos of my balances.

Hello, I recently ordered channel balances but did not realized that the sash supports are broken and I also need some pan am take out clips. I think I have found out the part number for the clips but I cannot find the sash support part number.

I just want to confirm, they look like your S377-30 (since they are 30" long, not counting the plastic). It is stamped: r 29-5. What weight would I need? Also, I need take-out clips and a top sash guide. Thank you.

I need 4 clips and two 25" balance

In the house I rent the windows are old from 1976. They are single pane aluminum. These little clips are broken and I was wondering if these Pan Am clips you have will work in my windows. I have attached 2 pics of the broken one for you to see

PLEASE NOTE MY PAST ODER NUMBER 1097683......ON 8/9/2018NEED TWO OF EACHTWO window part use to hold down the channel balance AND TWO Pan Am Take Out ClipMICHEL B.

Please advise which balance you recommend based on these pictures. The length is 30 inches and I?m thinking it is the series 377 channel balance however I am not sure which option to select. The only markings I can find show c 29-1. Thank you.

My balance is stamped (q 23 4 ) it looks like your 385 model being 5/8? but has 7/8? wings on both ends and a 1? shoe on the bottom. Your 385 is showing 15/16? wings and 1 3/32 shoe. Is it possible to get the size guide I need on that model. Please direct me in the right direction with this. The wi ... (cont.)

Balance of single hung window. Balance measures metal to metal 24". The stamped number is 23-1

I LOOKED ON YOUR WEBSITE IM ALMOST CERTAIN IS THE S385-30 PRODUCT CODE BUT WHEN I TOOK THE MEASUREMENT OF THE BOTTOM WHERE THE HOOK IS, THE END PLASTIC PIECE ITS EXACTLY 1'' NOT 1'' 3/32 UNLESS THE THREE THIRTY SECONDS IS SO SMALL THAT IM UNABLE TO COMPENSATE TO THE KEEN EYE BUT JUST MAKING SURE THA ... (cont.)

I need two replacement parts for one window

Width just over 5/8 inch Top to hole center 3/8 Top to bottom 3/4 Top shelf thickness 1/8 Top shelf extension 4/8

29-14 FB5 CMC ( 29-HP-44-45) also need the nylon top sash guide to be identified and offer a replacement. Please see the photo attached for the guide.

Need a complete set of window track parts. Can you identify from attached photos. Window was installed in the early 1970's in Florida's Tampa Bay area. Please quote complete set of parts for one window if available. Thank you.

I am trying to repair a couple of windows in a circa 1973 home located in Melbourne, Florida. I'm starting with the two smallest windows, but this could blossom into a rework of 20 more windows.... The issues I am having are that a number of plastic parts are broken and the windows don't slide v ... (cont.)

I have an ANSI/AAMA 101-88 Window that does not stay open. My Contractor says I need the things that hold up the window replaced. Please let me know if you have them, how much and eta. Thank you, Brett

The balance is 31" long. It is stamped 3030.

I have a house built in 1978 with channel balances. The take out clips are plastic not metal. Due to age, the plastic became fragile and breaks when I tried to pull them out. Do you know where I can get replacement take out clips that will fit. Dave

1.Windows are approximately 48x31- writings on balance says 2950 2. Windows are 34x30- writings on balance says 2930 Please include parts needed and cost for 4 windows of each size

Part is broken just wonder if you have this part since it is not included with the channel balance. It is part of the window.