Viewing all customer Discussions for:

S351-27 27" Series 351 Channel Balance

I'm fixing 12 Milgard vertical sliders, 11 are 30"L x 34"W (18.2 lbs.) and 1 is 30"L x 22"W. The smaller window has 2630V stamped on the channel balance. I did not see a number on the channel balance for the larger sliders but the style is the same. I will look tonight on the balances on another win ... (cont.)

My windows are hard to open and close, even though the balancers appear to be intact. Maybe buildup of grime/dirt? I tried to clean them, but didn't help. The numbers printed on the balancer are 2630 J.

2630 Length metal 27" Wide 1/2" Looking to replace 80 =priced? 100 =priced?

Need help identifying this window balance. This came off a white vinyl window markings on the balance read: 26 2 DT CMC 2 The balance is 27 inches long (not counting ends) The balance is 5/8 ths wide See pictures for additonal information. I need approximately 6 of these units.

Dear Sirs,I need a pair of new window channel balances. The metal part is 27" long.Best regards,Siegmar

Marked on the side is B.S.I 2640 (shown in uploaded photos). I do not see any brand on these black aluminum single hung windows. Thank you, Cliff P.S. I know my phone rotated the uploaded photos, if you cannot rotate them, let me know.

I am purchasing your model 351 block and tackle 27" channel balances for my windows. I have one window which requires a small, 9" channel balance, similar to the 351. Do you sell that?

The serial no. Is very hard to see as it's worn off but what I can make out looks to be : 26 4 FV CMC 52 Can you point me in right direction regarding proper replacement parts please ?

Hello I moved into a new house and there's a window with only one spring channel. I was hoping I could get one for the other side of the window or 2 if the pictured one looks defective. It has the markings "26 5 HU CMC 2" on the side and the metal channel is exactly 27" long. If you have any insta ... (cont.)

Hi, two balance springs of my window are missing. And the type is 26D SRS 77T B&T TN Balance, but I'm not sure what exactly that means. Could you please help me understand which ones I need to order? Thanks.

Hi there, I need a replacement for a 27 in channel balance labelled 26 4 IN CALDWELL. It is 1/2 in wide and 5/8 in deep. Can you help me? Thanks Mike

I am looking for replacement window channel.I enclose the label dhr 20 for a 1500 series Milgard.27" I need 8 pieces . Please direct me to the correct item.Kenneth

Bus no 2630

I just need to verify that I have selected the correct parts.I think I need 2 ea series 351 spring balances 24" long. to replace part number "23 4 CS CALDWELL, and2 ea series 351s 27 " long to replace part number "26 9 at CALDWELL".Also broke a take out clip so I want 2 ea; I think the part number i ... (cont.)

Geinow single hung non tilt window. Dimension is 45.25 inches by 29 inches high. The metal balancer is 27 inches long by 9/16; dimension is for the metal part not including the plastic on each end. The marking on the balancer is 26 6 CX CMC 7. One of the balancer is not working but we will get two ... (cont.)

I want to make sure I'm ordering the correct parts. Can you help?

2630 BSI FN stamped on the channel. 28" overall length. Looking for a right and left pair for one window. Hopefully the photos show enough detail or can provide close ups Thank you! John

Hi, How do I determine if I should use the Series 380 or S385?

My window sash is about 27 X 34. The old channel balance is 2640. I've ordered replacements from you but they don't work so I'm wondering if the channel balances we replaced were perhaps not the original. The new channel balances do not disengage from the take out clips when we pull down the sash. ... (cont.)

I need help choosing which replacement window balance to order. My window balance has the part number 26 4 KV CMC 9 on it. See the photos.