Viewing all customer Discussions for:

S351-28 28" Series 351 Channel Balance

The pictures are my old ones the stamp on the metal is 2730 thank you peter

I need help identifying the replacement channel balance. The stamp on my channel says 2730 AD B.S.I. The shoe has a depth of 1-1/16(worn down from 1-1/8?), and doesn't have wings. The metal channel measures 28". The sash weighs 16.5 pounds. Thanks!

looking for 20 caps to go on top of my window balances Top measures 1-7/16 x 1-1/8. overall height 1-11/16 width 5/8" under cap. 2 screw holes

Hi, I'm looking for a replacement for the part (pictured). After browsing the website, comments seem to have narrowed down to option 2740 for below models: https://www.swisco.com/28-inch/pd/Series-390-Channel-Balances/S390-28 https://www.swisco.com/28-inch/pd/Series-351-Channel-Balances/S351-28 1. ... (cont.)

I have Alenco windows. Only the bottom sash moves. I need a set of channel balance as well as a set of replacement retaining clips (the ones used to remove the lower sash). One of the clips has broken.The channel balance is marked 2720Q as shown in the attached photo. The metal part of the channel b ... (cont.)

I need 2 Balances. 1/2" wide. The metal channel length is 27 15/16"'s. The window weight is about 19.8 pounds. The window balances that were installed, are probably to heavy - strong for the weight of this window. The is a part number on one of the attached photos. Thank you.

need help for replacement. Blomberg Window, single hung, stamped 2740 as shown, 28" long, channel width 1/2"

Bar length 28" Stamp 27C Need fully assembled ready for install; ends attached I'm not handy :(

My channel balances are marked as shown in photo. However, the metal-only length measures 28". The overall length, including the top guide & shoe is 29". It seems my channel balances match your Series 351 in every way. But is the Series 351 metal-only length 30", or 28" like mine? Please advise so ... (cont.)

Hello,I am looking to replace balancing hardware on my windows as it is broken. I have few different size windows. I was only able to attach pictures for 28in length one and other one is 24inch length. Both are 1/2in channel width and end hardware is identical. Windows locking mechanism has Alenco o ... (cont.)

Metal channel is 28 inches. Stamp say 27 C bsi . Channel appears to be 1/2 inch wide and 9/16 deep.Need 1 5/8 top sash guide in black looks like part number18-008.S395 looks very close. Need to know weight option for C stamp. (2730) ?Can you help me confirm the model number I need? I'm ready to orde ... (cont.)

I need 4ea balance springs, metal channel is 1/2" by 28" without top & bottom pieces. #2740 stamped on side. I need 8ea of the little tiny clips the go on the sides of the sash. I need 2ea of the latches, holes are 2 1/4 in on center, opening for the striker is 3/8th of an inch.

Need some help in determining which balance replacement I need,

The bracket holding the pulley system to the metal channel is bent and broken. The channel has the number 2740CG stamped on it and the channel is 28 inches long. The spring seems to be in good shape!

I need a pair of 28" shash window balances. The ends are as per the photo's uploaded and it is stamped 2740 J.I would have bought the stock ones but they have wings on the ends protruding sideways, mine do not have these. ThanksRegardsKevan

Window measures 3 width 6 length Non- tilt Stamp 27C Measures 28 inches I need 2 left and 2 right For 2 window

Need a new Jordan Window balancer.

I am trying to install new sash window balance. My current one has markings saying 27 4 FW CMC 4. Which part number should I choose?

Hi, I need to replace two Channel Balance's, I'm not sure if I need the S351 or a different type. Numbers on the rail 27 4 CW CMC 9 length - 28" Width - 1/2" Also its not allowing mt to upload photos, its timing out. If you email me I can forward the pics to your email. Thank you Shar ... (cont.)

I have need for replacement counter balances on my Jordan windows non tilt. They all appear to have the same counter balance of 9/16" wide and the metal part is 28" long.The only numbers I can find are 27 9 and then CV horizontal stamp and then BSI vertical. The weights of the windows range from 27. ... (cont.)