Viewing all customer Discussions for:

19-005 Channel Balance Top, Winged

Hi there, Not sure if I have selected the correct part, 380, 1110, for this 12 " balance channel. Could you head me in the right direction please? Regards, Paulette

Need replacement balance although the old balance is stamped 28-G-70 the metal part of the balamce is 29" long

I Have in my cart S380-30 and S380-35 but my plastic piece at bottom of the balance measures 7/8 not one inch and I read some comments that I may need 029 (from Memory) on bottom and you have to make up. Please let me know about this. Also the bottom `Bubble Seal", please see photo, is not exactly l ... (cont.)

I need to replace 4 window balances. They are marked 2830 and also 28C. The length of the metal channel is 29". The width of the channel is 1/2". Each sash weighs 19 lbs. The top shoe appears to be a 19-005. The bottom shoe appears to be A 7/8" winged channel balance shoe #15-029. Photos are attac ... (cont.)

Hi,Ja-Ni in customer service told me to contact you to order custom window balances after I sent her the following email:Hi Ja-ni,I measure the front to back length of the lower shoe to be 7/8". The diagram from Florida Extruders says that it's actually 29/32". SWISCO lists a part #15-029 that is 7/ ... (cont.)

Alcan non tilt window. Channel balance stamped with 2910 W Need help with the ends!

Need two of these replacement window Chanel's please.

30" series 380 channel balance. Product code S380-30, Top Fitting 19-005, Bottom Fitting 15-005 1. Is the 380 correct channel balance; dimensions for Top & Bottom Fitting and overall length appear identical.Please advise on spring & pulley system 2. Can the 380 be used on both sides? 3. Since there ... (cont.)

2630JB

I need to order some replacement balance rods, but I wanted to make sure that I'm ordering the correct part. These are for a Linford window. The rod is 27" and is stamped with a #2640.

I need to replace single hung, non-tilt ,block and tackle window sash balances. Old part has 2940 BS1 stamped on it. Channel width 1/2", length of metal 30",channel depth 5/8". Both top and bottom shoes are winged. Your series 380 has the correct top shoe (19-005) but my old bottom winged shoe only ... (cont.)

The metal part is 23 inches and the with is 1/2 inch

I would like to place an order for custom window springs. I need two 30" Series 380 2920 Channel Balance, but with a 19-005 top and 15-029 bottom. I also need two 5/8" Sash Guide, 18-161. Thanks for your assistance.

Hi, my stamp says W2640, while I think I have narrowed down the series to two possibilities, I am not confident as to whether it is series 390 or 351. Are you able to help based on the picture? Thanks,

Hi, I'm trying to replace channel balances for 2 windows and cannot find a corresponding match (shoe) on your site. It's for a non-tilt window, 1/2" wide, 25 5/8" length (metal part only) balance. The winged top looks like it's the 19-005. The shoe is 1/3/8" from pointy tip to bottom and 1" side t ... (cont.)

Windows balance 1/2" width, 23" long; has the number 2230 engraved

Please help me identify the Balance I need to replace my broken Balance Please note that the shoe does not appear to be broken it is just that size. Thank you Thomas

There are two 30" per window I will need three total

I will need 6 of the S385-29 balances (2850 spring) with the 15-029 shoe.

Looking for 2 custom 2930 window channel balances with a 19-005 top and 15-029 foot. Could you please provide an estimate on time and cost to manufacture? Thanks, Mike