Viewing all customer Discussions for:

S380-27 27" Series 380 Channel Balance

I am looking for channel balances marked 26 4 IU CMC 2

July 28, 2023Please find attached details of my window balancer.* Printed on the lower end of the channel: 26-9 CS CALDWELL* The five attached photos represent one of two two window-channel balancers needed.* Total length of both channels, EXCLUDING the plastic parts at each end: 68.7 cm / 27.04 i ... (cont.)

Hopping you Have this ChannelsItem number has mark on the side of the channels27" Channelshas has mark on it horizontal 26 4 & Vertital BSI and Horizontal PPand 12" Channelshas has mark on it horizontal 11 5 & Vertital BSI and Horizontal PNI am assuming the first 3 numbers are the size of th ... (cont.)

My window channel is 27 inches long not counting the plastic ends and 1/2 inch wide. The marking stamped into the metal is 2630 CJ @ NE. I would like to purchase a new Ballance but I am not sure which one I should buy. Please tell me the Window Ballance I have and which one I should buy. Thank You, ... (cont.)

I have a Caldwell Manufacturing non-tilt balance that needs to be replaced. The photos of the end caps are attached. The length of the aluminum rail (not including the plastic end caps) is 26-15/16". The part number stamp is: 26 5 CX CMC 7. Can you please help me find the replacement part for th ... (cont.)

Channel length: 27 inches Stamp: 26 4 GW CMC 7 Manufacturer: Milgard (approximately 2003) One balance definitely needs replacing. But I have heard I should replace the other balance too. Therefore two needed.

Home was built in the early 90s. They are 1/2 wide and 27" long.

The part measures 27 inches, 26 4 GN Caldwell

15" Series 385 Channel Balance, 1420 for Option Will This Fit? Please verify. Thank you. See attached photos.

I'm trying to find a replacement part of a window balance. The stamp on the back of it reads 264 AW CMC 2. Can you please link me to the Swisco replacement?

Metal measures 27" long and just over 1/2" deep. 1" bottom plastic. Stamp is (03/8) Unique 26-0-30 and I have been unable to determine which is correct replacement. I need 2.

Please help me find the part number for the balancer to order for my Milgard single-hung window: width: 1/2 inches length: 27 inches weight of hung window: 19 lb If you need further information, I'll try to get them. I greatly appreciate your help. Thank you and have a great day. Louise ... (cont.)

Hi there!!! HELP!!!!! I pulled the parts and tried to identify the part online without bothering you guys but I cant. Here are some pics. ( Attached ) Can you please tell me what part I need so I can order them?? Also if for some reason they don't fit are they returnable?? Thanks in advance for you ... (cont.)

I need this window balance.

As seems common, my channel balance string broke. I'd like to replace the balance and have a couple of spares on hand too. The number on my balance is "26 3 DX CMC 7". There are no other markings on it. The metal channel measures exactly 27 inches in length.

Hello, We need 4 new balancers, but we are having trouble locating them. The ID on the balancer displays 26-4-HW-CMC-11. Do you guys carry this in stock?

Need to repair 2 windows with 27" metal casing, labeled 26 4 EQ Caldwell Need to repair 1 window with 27" metal casing, 26 4 HP Caldwell

Please identify the springs I need so I can order them.

Decided to replace block and channel from Swisco because window wouldn't close all the way without a lot of force - this caused the screws in the lock lift up and become dislodged since it was the only thing preventing the window from coming up. Ordered the new part (2650) and the same problem is ha ... (cont.)

Looking for the sash weight option stamps on window balances. There is an ink stamp that says "26 2 JT CMC 4". Does that indicate a 2620 stamp? 9 - 13 lbs? It would make sense, I think. But I was looking for a 4 digit number someplace.