Viewing all customer Discussions for:

S390-27 27" Series 390 Channel Balance

Please identify and provide me a part number.

Hello. I was trying to find two of the springs in the photo. Not sure if they ever had wings or not as they could have ground off. I would need 2 of these '2640'. I also have 4 similar ones but they ate '20' lb ones (27") I also need one those spring clips that you set when you being the window ... (cont.)

Team, I am in need of 2 each sash for an IWC Single Hung Window ~ 34 x 60 inches. Any assistance would be greatly appreciated. Thank you, Matt

Numbers stamped on the channel as shown. Can you help me id this balance.

Hello, I need some replacements. Please see photos. Thanks, Marcus

Hello, Can you help me identify the window balance and shoes? The number on the balance is 2630; the total length of the balance is 26.9 Inches. Thank you for your help!

I'm trying to find the correct lifts to order to replace the broken ones on my window. Will you please help me find the correct parts based on the photos that I uploaded? The lift has the following stamped on it: "26 4 HX CMC 7".

I need to order 4 channel balances just like the attached pictures. I spoke with someone who told me to send pictures and you would be able to get the correct ones for me. If you have any questions or need further information and my credit card number, I can be reached at the number below. Thank you ... (cont.)

Looking on your site I see two possible item that looks right. s351 or s390. Where do I measure to determine which balance I need.

Swisco Folks:Just spoke to one of your reps and I've uploaded two photos of Milgard Balancers for identifying the proper replacement. that I need a replacement for two of them as springs are rusted.Stamped number is 26-CLength end to end metal (not including white plastic) is 27 inches. I need two ... (cont.)

We need to order 8 sets (16 total) with all associated hardware. I will attach a picture of the part and part number. Please let me know when they come in.Thank you Carol

I need 8 of these hope you can help

Window channel balance, the window is about 30" and the channel balance is 27" with half spring and half chord. the foots are plastic and there is no identifying numbers on any of the channel balances. On the top of the spring side, there's 4 dots on the side of the metal on each side. The brand is ... (cont.)

My windows are hard to open and close, even though the balancers appear to be intact. Maybe buildup of grime/dirt? I tried to clean them, but didn't help. The numbers printed on the balancer are 2630 J.

2630 Length metal 27" Wide 1/2" Looking to replace 80 =priced? 100 =priced?

Need help identifying this window balance. This came off a white vinyl window markings on the balance read: 26 2 DT CMC 2 The balance is 27 inches long (not counting ends) The balance is 5/8 ths wide See pictures for additonal information. I need approximately 6 of these units.

Dear Sirs,I need a pair of new window channel balances. The metal part is 27" long.Best regards,Siegmar

Marked on the side is B.S.I 2640 (shown in uploaded photos). I do not see any brand on these black aluminum single hung windows. Thank you, Cliff P.S. I know my phone rotated the uploaded photos, if you cannot rotate them, let me know.

Please provide a recommendation for the replacement of my existing balance. photos attached. the stamp is 26 DS BSI NL 36. I measured the length it's 27 inches and it weights 32 lbs on the scale. I ordered (#1243804) the S390-27 : 27" Series 390 Channel Balance from your site. I hope it's compati ... (cont.)

The serial no. Is very hard to see as it's worn off but what I can make out looks to be : 26 4 FV CMC 52 Can you point me in right direction regarding proper replacement parts please ?