Viewing all customer Discussions for:

39-337 2" Crank Handle Extension, 11/32"

Hi I have a 2 story front room with I believe folding truth handles in the 2nd story casement windows. Those are out of reach but I still want to open them. I have a telescoping pole that I could add an attachment to but wasn't sure if there was a better setup or if you could point me towards the at ... (cont.)

When we remodeled our kitchen, we were unable to install the normal crank handle for our Milguard window. The contractor installed an extender and then a round handle to allow us to turn the crank (See photo). This handle now needs to be replaced and I have not been able to find a replacement in ... (cont.)

Good morning,I would like to replace the current cranks shown in pictures with new cranks. The current brand is Loewen and were electric windows. We are going away from the electric windows and going back to hand cranking them. The only problem is that these windows are 12 feet off the ground so I n ... (cont.)

I have a clerestory awning window made by Milgard The crank was modified to put on the hex head as in the photo I've also included a picture of the head of the operating pole It's almost impossible to get the pole cap to fit on the hex crank and I want t different system/configuration I found t ... (cont.)

I had previously sent in a question about finding an extension for the existing cranks I have for these K&K windows or an extended crank, longer than the ones I currently have.I believe my original case was 36451934.I had plantation shutters installed over the existing windows which extended the ... (cont.)

I am looking for a window crank handle extension that works with Truth hardware crank model 45240 10 (white) thanks Mr. Lee

So I'm looking for a bit piece that I could run to a power drill so I can fit over that little metal piece to roll the window down and up. As my hillbilly powered windows. It is also a small piece.

What size spline does this handle have if I want to add an extension or universal joint

Hello, I just had a bay window cushion made and I cannot turn the crank without hitting the cushion. Would a 2 or 4 " crank extender solve the problem? My window was made by Pozzi in the 90's.. Thank you!

Following kitchen renovation, the window on the pictures will become too far to reach the crank, so I wanted to replace the crank by an eyelid (bronze) Would part 39-336 be sufficient, or do you think I would need more to set it up? Do you recommend other configuration (knowing the access will be h ... (cont.)

In the first picture the threads are below the sill. Need an extension. In the other 2 we are removing the wooden sill and replacing with granite which will make it 3/4" thicker so need extensions for those 2 Windows. I measured these as 5/16, 12 teeth. Also need the hoods that are missing ... (cont.)

Hello. I have awning windows installed high in my livingroom with 2x8 stud walls. The depth of the walls means I need an extension from the crank pinion on my window to the edge of the sill so I can open them with a pole. It appears as though you produce such hardware. What details do you need to id ... (cont.)

I am looking for Extra Heavy Duty Crank and Rail to replace the existing crank for steel window which is very old and very stuck. We replaced the original cranks with the ones you see in the photos, however most of them were broken because it is not strong to open heavy window especially when start ... (cont.)

Hi, I

Hello, Hope you can help me with a threaded female end that fits the 4th image on a skylight mechanism. I don't have the brand name - not shown, but the whole thing looks like this one: Skylight-operator/pd/Awning-Window-Replacement-Operators/39-379 An inelegant solution would be to glue the 2 ... (cont.)

...we would like to add marble sills to our new windows, but this would require a crank handle extension of about 1"...does this exist...? Thank You. Tim.

Hello, I have a skylight window with a crank handle. Saw your 2" Crank Handle Extension, 11/32" Product Code: 39-337. Does this product fit any type of crank handle? My crank handle is like your Crank Handle, 11/32" Product Code: 39-114L. Also, do you sell the pole ( 10+ feet long) that woul ... (cont.)

Hello I just purchased a home with 15 casement windows which are opened & closed daily. The hole in the existing handle appears to be 3/8 inch. As you can see, the small area makes this a long process & usually leaves my blood behind. Also, my fingers aren't strong enough to open the window entirel ... (cont.)

I am looking for 6, 2" extensions, and four 2" crank handles. With screws for mounting the two to the window crank. I gave you the measurements. The extension is 2" long, I need 6 of them, the crank handle shaft is 1.5/8" in length. and the screws are 3.5/8 to bottom oh head. There are no names ... (cont.)

I have a customer with atrium windows missing one of these handles. I thought these were Anderson windows at first Glance so I took the info I had: (house built in 1995 and bright brass hardware I was able to cross eliminate & get a handle mailed to me. Unfortunately it was wrong the angle & thickne ... (cont.)