Viewing all customer Discussions for:

S385-30 30" Series 385 Channel Balance

I need 4. See attached photos. 1/2 inch channel overall length is 31 1/16 tip to tip of the plastic ends. Stamped "s 2910"

30" metal to metal/height 5/16"/width 1/2" Thank you for your assistance.

28.5 ES CALDWELL 29.4 NH BSI 21-9 BPS CMC 43

I need to replace some channel balances on some Milgard nontilting windows. Channel is 1/2 inch wide and 30 inches in length.

Stamped with "29 3 B.S.I 0L". The 'B.S.I' Is perpendicular to the rest of the characters. I believe the windows are from a company called Pacific Window Corporation that no longer exists. I have several windows that are not working properly. They're different sizes, & probably have a small variet ... (cont.)

Hi, the cord is broken on the other unit. If you can identity I would greatly appreciate any relevant information. It measures 30 inches. There is also a plastic adjustment screw on the bottom. Thank You, Patrick

Hello, see attached photos. I am looking for a replacement. Depth ~0.5". Length of channel 30". Thank you for the help :).

I would like to know which replacement part I need.

Hello there, I have a question if I can have answers right . I am trying ti figure it out what type exactly have. Ans I need so bad to replace. There are just numbers and I measured the balance which is exactly 30" long. See the picture below please..

Dear Swisco, Please help identify channel balance in the attached photos. The metal frame is 30 in long. Thanks, Kevin

I have 11 windows of several different sizes. The all are the same style. From looking at your website I think they are style 385. The metal channels are 1/2 inch. The shoe part is 1 3/32 inch deep. I am sending pictures to make sure I order the correct ones. The metal channels all are stamped ... (cont.)

BSI 2915 LH from 1999 or earlier

The stamping making is 29 per photo, the total metal stem is 30 inches. Which part number should I order? Also do you sell the clip that goes into the window side, as I am missing one? I also need to order similar with the stamp marked as 33 and the metal length is 34 with similar ends per attache ... (cont.)

Goal : Buy 20Weight of the window : 20 lbsLength of the metal part when I measured shows 30 inches but the stamp shows 29 as the first two digits as shown in the subject line above. Hence confused.Length, including the two end plastic pieces is 31 inches.Inside width of the channel is 1/2 inch.Quest ... (cont.)

need 2 balances to replace old ones. Numbers stamped show 29-4. See attached photo. thirty inches long, metal to metal

I believe I've got a 380 channel balance. My shoe attached is 1" and top attached is .5". It measures 30" long. The number on this channel balance is 2990. My windows are Harcar. Let me know if you need any other info. Thank you.

I need to replace to 30 inch by 9/16 channel balances. Can you help me identify the part I need to order using this information? Thanks

--Length of the metal channel: 30 inch. --Stamp printed:"2975 (a logo) AC". --Manufacture: Milgard Window. It was probably from 2007. --It's a single hung Milgard window. --Need 4 balances for two of the Milgard single hung window.

Hello. The channel balance (metal part only) is 30" long. It is 5/8" wide on the back. It weighs 7.5 oz. Please help me identify and order the correct balance. I will be sending another email for a different window. Thank you.

These photos are 2 balancers that are from the same set (6) windows ( same size and weight) they may be from 2 different manufacturers. They are 9/16 by 30". Please let me know what counter balance you recommend. I did weigh one of the windows and it weighes 41.4 lbs.