Viewing all customer Discussions for:

26-021 Pivot Bar, 2-1/2"

This pivot bar has threaded holes. I need to identify the part number please

2.5" long, has the number 6236 on it. Thanks for your help.

I have original windows in our home built in 2008 that appear to be Millgard, however all the Millgard balances I find online look different than these and don't seem to have a pivot shoe. In a few of the windows in our house the pivot shoes seem to have warn and come out of the balance. I did l ... (cont.)

I am looking for a replacement for the block and tackle sash lifter shown in the pictures. The windows are approx. 20 yrs old and the sash is ~18 lbs. I will need a right and left side if they are handed. I will also need replacements for the pins that go in the bottom of the sash. Thank you fo ... (cont.)

Hi, looking for this part with the spring coil that is connected with it.

I need to replace all the balance shoes in the entire house which is 15 windows that are 3-0 x 6-0 windows. The tension on the balances is pulling the balance apart from the shoe. The balances themselves are in good working order but my concern is will the new shoe fit into the old balance. ... (cont.)

The lower sash of the window that was installed 10/14/2004 won't stay up. I have taken off the lower window and the coils on both sides are all coiled up on the bottom. I can't figure out what company made the window. The coils look very different than all the YouTubes videos I've watched to get ... (cont.)

The piece is broken. It seems to be T-shaped, 1" wide, close-cam -- see photos. The part number is 4610108. I see that you have suggested your part 15-195, but that is 1-1/4". You also have 1" part # 15-194, but the spring hook seems to be different: in my case it is angled down (see the pictures) ... (cont.)

Pivot shoe is 1/2 inch thick, 1 3/16 wide unlocked 1 5/16 locked 2 1/8 tall Pivot bar is metal, a little longer than 2 1/2 1/8 x 1/4 the tip is 1/8 x 7/16 x 1/16 thick and a threaded hole 1 1/4 in from the end.

Hi. I'm looking for the pivot bar as in the pictures. Total length: 2 3/4in

My windows tilt in and bottom sash is removable. When tilted in, they lift out of a sliding part that has a string along each side of the window. There are 2 metal parts that are t-shaped attached to the sash that fit into the slides. See the attached picture. They feel like cast aluminum. I on ... (cont.)

We are in need of about 40 of these.Thank youBillie

A Swisco rep told me this shoe isn't around anymore. Do you have something that would work?

I need to replace a missing pivot bar the remaining pivot bar looks very much like 26-021, except that it has a flare below the head. Do you have a replacement product for this?

I need to replace these two pivot bars for my 32.5" Mastic window.

1/2 inch thick 2 inches height 1 3/16 inches width

27 1/4 inch tube inside a 12 1/2 spring , with cord to hold up window

I need 4 window pivot pins. On one side is a no. 2

Hoping this is what we had break on a dining room window! This is the other pivot bar in that same window. Match? If so, I probably will/should get more than one (just in case, order 6?). Your help is a lifesaver as it's been immobile except for cleanings!

I would like to replace the spring balances on some double hung vinyl tilt windows in a mobile home that is about 20 years old. The upper ones are working fine but the lowers new replacing. The channel is 3/4" wide and the window heights are either 15" or 29". Do you have anything that will work? ... (cont.)