Viewing all customer Discussions for:

26-412 Flared Pivot Bar, 2-1/2"

Hi- could you help me identify this part? These two bars broke out of the pivot of an upper window sash (the tilting kind). The bar is identified with the number 1074, the holes are about 3/4" apart. Thanks!!

I am looking to replace the pivot bar on my international double hung windows. I hope you can help me. I went to our glass company here, but the holes don't line up with the window. In the picture the first one is what I am looking for. The second picture is the broken one.

Hi! I am trying to find pivot bars for the windows in our house. They look like the ones shown on the attached photo. I've noticed you ask for a photo of an unbroken pivot bar in many question/posts like this but I've had no luck finding one so far. I've tried to remove a pivot bar from several wind ... (cont.)

Were in Hawaii we think the window is International Windows Before they Bankrupt. We are not sure. But we needed to replace the flared pivot bar. Not sure if your 26-412 will work. Do you have a suggestion.

A customer's sunroom has 6 double hung windows all with broken aluminum pins similar to your #26-412. The number cast into the original part is "1074". Im looking to see if there is a steel replacement. Thanks.

My 20-year old American Craftsman windows have sash pivot bars that look almost identical to your part # 26-400 Alas, the measurements a just different enough that your part will not do. My part has stamped (1054)overall length 2 1/2" (as opposed to 2 5/16") space between holes in 3/4" (as opposed ... (cont.)

Farley Windows installed in 2006 by builder/developer. What is the best option for the Tilt latches which are slide in type. Also the sash pivot bar is nylon. Photo is part of the pivot bar. What is the best replacement option and is the pivot bar enough or do I need other parts. Thanks for your ... (cont.)

I need several replacement "posts" for vinyl double hung tilt sash windows. The pictures show the vertical tilt window pivot shoe and the broken (pot metal) post/tab/cam from several angles. I do not know the manufacturer of the windows. I'd appreciate any help you can provide. Thank you. Russ ... (cont.)

We are looking for (2) replacement parts for our North Brunswick window. The window is a double hung window. 35 3/4 x 45 1/4. (40WS35645211NHCHD) 11656059.1. 05/04. Z98 Parts we are looking for are in attached picture. Measurement: 2 1/3 long by 1 inch at widest point.

I have a double hung window that was installed about 15 yrs ago and now my upper sash window has 2 broken pivot bars. I have attached a picture of one of them, is it possible you can match these? Thank you in advance for any support you can provide me. Peter.

Pivot bar. Missing the tip. Top side reads 1074. Bottom side is indented and has a #8 on it

I bought double hung windows from Home Depot years ago. There are small metal parts (one pictured here) that have broken. I think they are part of the balance. THey go into a hole at the bottom of the balance and are inserted in a hole on either side of the bottom of the upper windows, and they keep ... (cont.)

No markings on Windows double hung top window

A screw goes thru it into a "U" channel that goes into a pivot locking shoe. Only used on the upper sash windows.

Pivot shoe size 9/16 thick by 1-1/4 wide by 2-1/8 tall pivot bar 2-1/2 inches long

I have three windows that were installed in the 2002 timeframe and the pins that insert into the weights have broken. They are approximately 2-1/2" long and are held in with two screws. I have attached pictures of the pins hoping there are replacements I can order.Thanks, Kelly

Looking to replace this and another pivot pin on my window. No identifying marks on the window unfortunately. Any help would be appreciated. Thanks in advance.

Hi I have a hang window non tilt. one of the parts is broken which caused the top half of the window to slide down. I'm try to order replacement parts, but I am not sure what the part is call, i have attached some images. can you please help? Thanks, Steven

I have several silverline windows (circa 2005) pivots, tilt locks, pivot bars and channel balances need replacement.

I'm looking for constant force balance replacement parts This is a double hung window, the windows tilt out and the pivot bar has a notch in the shaft and the shaft has flange like ends (see picture). One spring broken and then a second and then a third. I'd like to know what my options are. ... (cont.)