Viewing all customer Discussions for:

S395-30 30" Series 395 Channel Balance

Need need window balances for my PGT slide windows. Here are the photos.

I have a lot of windows and going to start replacing them Window by window.

Channel measurements: 30" length (not including ends), 1/2-9/16 wide, 9/16-5/8 deep Markings on channel: 29 4 BX CMC 7 Window is made by PGT meets 2004 hurricane standards Window measurements: 34.5" W by 32" L I am the home owner and very able engineer

I have these that I would like to order. It's from just one window. The window is 50" length and 32" high. The metal balance without the plastic end clips is 30" long.

The channel measures 30" in length and is 5/8" in depth. Stamped on the channel is 29-4 BSI. What replacement part do I need? Thank you.

The plastic stoppers dried out & broke off allowing the spring to pop up. Metal balance is 30" long. Rod is 1/2" x 5/8".

Channel balance spring 29-5 GA2 CMC5 Need 2 of them

Hello - I am looking to replace 2 pair of Caldwell balance window springs that are labeled 29 4 BP Caldwell. Can you help. Pictures attached.

this appears to be a Series 395 with 19-005 top and a 15-001 bottom. the aluminum tube measures 30". However, there is stamping on the channel that notes 29-5 and smaller letters PA D31. By chance does the 29-5 indicate 29" length despite the 30 inch measurement?the window sash weight 13.9 lbs so ... (cont.)

Hi, Looking to replace window balance, I have found the following markings on the broken balance: 29-4 CA2 CMC 7. Which part number will be a match? Thank You Mike

Hi, I'm looking for a replacement for a broken channel balance. The number/marking on this balance is "29-3 0715 VBS". The measurements are:Length = 30"This looks a lot like a match to the Swisco 385 series. I am guessing the marking "29-3" on the broken balance means 2930 option for a sash weigh ... (cont.)

have caldwell springs marked 29 3 EO the metal portion measures 30 inches long is 1/2inch wide and 9/16 inches deep,,the plastic portion at the bottom measures exactly 1 inch, need two of these springs,also need 4 of the little white clips pictured. Question are there any other parts I should pur ... (cont.)

Could you direct me to the correct channel balance to replace this broken one. Also would you be able to tell which top channel guide would go with these? Windows are PGT brand.Also the channels balances are 30" long.

Hi, The house I live in has 20yr old, single hung vinyl windows which have always been difficult to raise and lower. My thought is the balances are for much heavier windows. The actual window itself weighs 28lbs. The window pane which opens is itself 31". The tag in the window states series 8300, H- ... (cont.)

sash guide has no number but drawing shows the dimensions. Window channel balancer have numbers 29-5 BHS (2) and 29-4 (2) the metal part actual length dimension is 30" Would like to purchase 4 sash guides and 2 each of the Channel Balancers Could you please identify the correct replacement parts ... (cont.)

The balances are metal casings with springs and strings inside of them. The metal measures 29 3/4 long with the plastic tips on top and bottom it measures 31 inches in length the width is 5/8 inch. There is a metal clip at the top picture sent. There is a plastic piece screwed to the window which me ... (cont.)

Hello I have a broken balance spring and took it out and the only markings I found were as follows 29-3 0113 VBS Can you help identify

Hello,can you please help me order viking CHANNEL BALANCE "2930"I need 2 of those plus the hardware for the sash and for the window.Thank you!

PGT window ballace

PGT window balance