Viewing all customer Discussions for:

15-001 Channel Balance Shoe, 1-1/8" Depth

Larger balance has m 40-4 stamped on the side. Smaller balance had 17S23 stamped on the side. Both are 1/2" in width. Smaller balance is 18" in length, larger is 41".

My Window Channel Balance part has the following characteristics: 1. Length: 28" 2. Channel width: 1/2" 3. Stamp on the channel: 2730 4. See attached pictures Please assist me in finding a right replacement part for it. Thank you.

I have non-tilt sliding windows with 27" channel balances (I think). They have been non-operational since I purchased my house and I dont have any knowledge of the make/model other than "IWC" logo on the latch. I tried to re-attach the balances, but they won't stay attached. It feels like the spr ... (cont.)

This is in regards to the above order. Just want to make sure I am ordering the correct parts. 28 3 Caldwell LL is stamped on the metal. It measures from metal to metal at 29". The metal is beveled at the edges. The window weighs approx. 20 lbs. Happy to answer any other questions. Thank you. ... (cont.)

Please recommend which balance to order. I can not tell which series is appropriate. Attached are several photos that should help identify the channel balance. You may be able to read some dimensions re the top and bottom pieces. The notations on the side read: 2030 BS1 EL The length is 21". ... (cont.)

Part needed: Caldwell 29 - 3 - FQ 30"

the ones i have are 18-166 and 16-002. i also have the rivets and the rivet tool. the piece i need now goes on the bottom of the window on the metal piece.

My windows are made by Alenco, and I'm assuming they were the originals in this home Lancaster California built in 1989. They are worn out and need to be replaced. I'm attaching photos of one of the balances. And here are the measurements: length from plastic tip to tip = 29" (metal only is 28" lon ... (cont.)

I need help on what needs to be ordered. I've attached pictures to help identify the parts. Your video's are quite helpful and are the reason I'm contacting you for replacements. 3 - marked with 2840 2 - marked with 2830 Thanks, Greg

I need some replacement balances. The channel is 1/2" by 5/8" with an outside hemmed edge. The writing on the back is "28 3 10 CALDWELL" The metal channel is 29" long NOT including the plastic fittings. I am pretty sure the top fitting is 19-002 because it does not have flanges. The bottom sho ... (cont.)

Hello, I am trying to replace a 14 yr old Caldwell channel balance and I need your help please? Picture# 1087 shows the part# printed on the channel. The other pictures show the top and bottom clips. Here are my measurements: Channel (metal portion only) 28" Long Channel (total length from c ... (cont.)

I need two channel balances as pictured. The numbers on the existing: 16 1 BSI RN The measurements are shown and are 18 inches end to end- 16 and 7/8 inchs metal to metal.

These are the original no tilt windows installed around 1992 The channels will not stay installed Could you quote me for a set of balances and all implacable clips etc Thank you so mulch

Need to identify parts

I need to replace the non-tilt window channel balances in my 1990 Viking windows as most are a huge struggle to close. The channel balance shoes, tops and caps are all the same. The only one I can figure out to match your parts is the cap which is number 18-009. The stamps on the 1/2" channel ... (cont.)

I need to replace my channel balances for my Viking windows. The balances I have are 29 inches in length and 1/2 inch width. They have a stamp on them that says 2830n (or upside down u). I have sent pictures of the hardware on both ends.

I need two Channel Balance for a non tilt window, width is 1/2" and length is 31" from just ends of metal case. Numbers and letters on metal case: 30 4 HV CMC 7. I have additional photos if you need to see more.

Hello! We are looking for 4 more window balancers just like this one. We took this out of one of the existing windows. We've had bad luck with ordering parts online only to get them and have them be the wrong thing, so rather than just ordering a generic window balancer, I want to make sure it's exa ... (cont.)

I'm having trouble with the stamp option. I need to replace 4 balances for 2 different windows. One is stamped 28 1/4 3 E H, and the other is stamped 28 1/4 3 C H. Can you ID. The correct ends for me too? I would really appreciate it. Can you help me find the right replacements? Ray ... (cont.)

I need to get two replacement balances for my AlenCo Window. I've attached four photos for your review. It has part 2740 stamped on it. The metal piece measures 28 inches. Do you have a replacement for this balance? Thanks,