Viewing all customer Discussions for:

15-005 Winged Channel Balance Shoe, 1" Depth

I have a 24 4 BN Caldwell Window Channel whose chord has broken. Do you have replacement parts? Can I just get the chord or do I need the whole channel? Thanks, Carlos

I need to figure out which replacement I need. It is 1/2" wide and the only markings I find are "22 4 G/Y Caldwell"

Good afternoon i'm in the process of replacing a milgard window channel balance. the part is stamped with the following: 32 9 aw cmc 2 the balance is measured 33 inches long 1/2 inch can you advise on the replacement part --- i believe it is 33" series 380 channel balance option 3260 ... (cont.)

it's 21" long for single hung milgard window. which parts do I need to replace the old one pictured Thank you.

I need a channel balance to replace Caldwell HM 32 4. The metal channel length is 33". Thanks John

Good Morning, Allow me to send you five photos of a broken balance I would like to replace. It is a 1/2

I need to replace a channel balance for a non-tilt window. I think I need either a series 350 or series 385, but I don't know the difference between 19-002 top piece and 19-005 top piece. The balance I need need to replace is marked 26 4 JR -- it is 1/2" wide and 27" long A couple ... (cont.)

Hello

Please refer to attached that I explain the window channel balance with picture and measurement. Please advice me how to make order and which is order number of window channel balance in website

Hello, I need to replace 6 of my balancers and also need a few take-out clips. I've included pictures of the numbers on the balancer and inside the window itself.

Hi, I need to replace a broken channel balance for a non-tilt hung window. I am unsure which exact part I need. I uploaded some pictures, can you help me identity? Kjell

I need a replacement for a channel balance. The marking on the balance reads: "36 4 GO CALDWELL". The overall length of the entire balance with shoes included is 38-inches. The width of the plastic shoes measure to be 15/16 of an inch. The length of the metal balance without shoes is 37-inches lon ... (cont.)

Hi - I'm looking to replace a few balance springs on vinyl window mfg in 1994. It looks like they are Caldwell markings 31 9 38#, length 32". Guessing S380-32 opt 3165 would work. The shoe is ~ 1" x 1"

I'm pretty sure, but can you confirm what I need? Thank so much, T

Window balance ( Identify) Pic.#1: piece that attaches to window panel frame. 2 1/4"long, 9/16"wide. Pic.#2&3: piece on spring end of balance.1 1/4" long, 15/16" wide at tabs. Pic.#4&5: piece at string end of balance.1 1/16" wide from tab to back, 1 1/16" long from where angled end goes int ... (cont.)

I think this is the channel balances I need. The metal part is 33" 33-inch/pd/Series-385-Channel-Balances/S385-33 The only Marking on it is 31 3 IP Caldwell It is on a Warnock Hersey Series 810 Code PP-0403

Stamp is 36 4 CALDWELL JM The metal channel is 37" Bottom shoe is approximately 7/8" 1/2" Channel Balance Need to know the Series 380 or 385 or other. Need top guides for this window.

27 inch Markings read. 26 4 go cmc 1 Wasnt sure if i need 15005 for bottom and 19005 for top

Hello, I have this window balance from an Empire Pacific EPI window that is about 12 years old. Please advise on what to order & I will happily purchase from you guys. Thanks! Devin

This window was installed about 24 years ago. The metal portion of the balance is 30" long. The marking is 2920Y. I will need one for each side of the window.