Viewing all customer Discussions for:

15-005 Winged Channel Balance Shoe, 1" Depth

I need to order replacement balances for three Kinco non-tilt windows. Attached are the pictures of the three different balances along with pictures of the tops and bottoms. Here are the markings of the balances: 24 9 JW CMC 11 28 4 KW CMC 11 29 6 KW CMC 11 Would you please let me know whi ... (cont.)

Good morning, I have Nuair Windows, installed in 2005. Attached are pictures of the top, bottom, code and the length. Please email with parts info. Thanks Cindy

we just ordered a plastic sash guide for our norandex window. It was the guide screwed into the removable window. Got that replaced, but see the pulley on the balance channel is broken too. It is a 1/2" X 35" with a number of 3440BSI on the metal part. We can't find that number in your product li ... (cont.)

The window ballast part is 30 inches in length from each end. There is a marking of "28D" stamped in the metal. This window is a basic type of window that appears to be very similar to the type (based upon the push mechanism) featured in the following Swisco demo video on youtube.com titled "How to ... (cont.)

Failing, broken, and missing channel balances on Philips windows. All windows same size. They weigh 23.2 lbs each. Windows are terrible to operate. All channel balances are marked 25 5 EL Caldwell. Hope that is enough information to determine what we need. The windows are in the home of an eld ... (cont.)

The windows I believe are Aluminum and either were installed around 1987, when house was built or 1999 ( I saw that date on some of the windows), which could be just the window panes changed and not necessarily the whole windows themselves The balancers are of two lengths 18" has a side stamp (17 ... (cont.)

This is a 26" x 1/2" window balance. I need to replace these on 2 windows. The stamp is 25 4 HP Caldwell. Thank you.

I was told the window is a Kinco from the builder. House was build in 03 or 04. The window is 30" tall. It is also 35" wide and 23.5 lbs with a metal frame. Number on the part is 29 4 LV CMC 2. I'm sending you pictures of the channel balance, but I may have to send it to you because I'm havi ... (cont.)

Need to replace a Milgard 33 " 1/2 " channel balance. Code on balance is 32 5 GW CMC 11. What balance of yours will work?

The number stamped on the part is 26 4 BSI PO (also included in an attached image. The channel length is 27 inches, width 9/16 (1/2) and opposite width is 5/8. I am interested in purchasing a replacement channel and one take out clip.

Hello, I have a broken channel balance that has the signage "13 3 DU CMC 2" (pictured). What is the best replacement part for this? The channel length is 14", and width is 9/16". Both end parts have "wings" Thanks! Vega in San Jose

Hello I need to get the correct part number for my channel balance. The length of the channel is 29", width 1/2". It appears that S380-39 might be correct but the width of the shoe is a little bit shorter than the 1" marked in your photo and I am not sure of the extra code I need. I have includ ... (cont.)

My balancers look like the 380 series. The metal part is 17" long and is stamped with 16E USB. The sash weighs 22lbs. It looks like the balancers only go up to 19 lbs, though. Do you have one that will work for me?

1/2" wide, 30" long (metal only), Non-tilt channel balance 29-9 FA2 CMC 9

I have acquired 25 used aluminum windows that I plan to install in an older downtown building remodel. The balance mechanisms all need to be replaced. I don't see a distinction between 104 and 105 shoes. The tops on mine appear to be 19-005. The balance rod is stamped 2340, so I assume that 23" ... (cont.)

Hi there, I have a channel balance to replace that has the numbers: 28 4 CALDWELL FM stamped on it. I don't see any numbers stamped on the plastic ends :(. The length is 29 inches not counting the plastic ends. Thanks!

My channel balance is 28 inches. The ends seem to match, but want to know if 004 and 005 are different. Also, my stamp is 27 C.

My channel balance has the numbers 38 and 2990 stamped on it which I don't see on your list. It is 1/2" x 30". The window measures 50" wide and 30 1/2" tall. What balances should I order?

I need to replace two balances and sash guides in one of my master bedroom windows. The parts are shown in the attached photo. My best guess is that they are 350 series (28" long). Both top pieces (19-002?) have broken tabs where the sash guide engaged. The two sash guides (18-009?) are also cracked ... (cont.)

there is a 28 f stamped on the back of the channel balancers. They are 29" long and 1/2 in wide but I can not find the exact top and bottom on you site. Tim