Viewing all customer Discussions for:

36-004-10 10" Stainless Steel 2 Bar Hinge Set

I have 4 windows....need four left and 4right (side frame) lock (8 total) and 2 right and2 left for (bottom frame) sill crank (4 total) (at least I think that's what they're called...)ThanksLinda

looking for replacement hinges/pivots for milgard windows these parts are stainless also need window seals

This track has the slide built into and pivots on a small plastic part, (exactly at the corner) notice photo with red shirt, the end of hinge point on track is raised slightly Our local suppliers keep trying to give us tracks with slides that hinge about two inces from the end. This results in wind ... (cont.)

This window when shut tight still isnt being pulled snugly into the frame. Hinge problem? Or that metal part where the window pivots? Maybe i should order both parts. Can you ID?

Caradco company my name is ron

i am looking for replacement hinges (right opening) for Weathershield casement windows installed in 1995. The plastic covering on the guide tabs have deteriorated and broken. see photos. The length of the hinges are 7.5" x 5.25" in length (with no markings). Can you help find replacements or altern ... (cont.)

I am looking for a windows part. Does not have any identifier. Just number 49 and TRUTH USA. Picture of it attached

Hello , The operating arms and brackets of our windows are old and need replacing. We are trying to find which parts to buy. I uploaded some pictures to help identify Can you help us. Thanks Willy and Flavia

Part number inside 40942-A

Home Depot brand windows I am trying to find these pots I bought the windows from Home Depot about 15 years ago they are crank out windows I need the mechanisms for that I also need the rubber bushings for the locking mechanism on the side of the windows if you can help me I'd gladly appreciate it ... (cont.)

Casement window crank mechanism rusty and not turning the window fully shut.

Can you help me identify the black plastic piece in this photo? These are broken on two of my windows.

I think I need the "L" shaped part. When I close the window(turning the operator counter-clock wise), it does not close completely. Something is stuck at the end of the closing cycle, so the window does not close tightly. The window is still open about 2 inches. That is all I can do when I close th ... (cont.)

Hi, my name is Ed Pelli (401-487-3479).I was told that the hardware manufacturer for window is Truth Hardware;the white,right-hand crank (operator) is 5.5"wide(total length) with 2"mount where crank handle is. Hinge pieces are same dimensions for both top and bottom and measure 7-3/4"wide that atta ... (cont.)

I hope you carry replacement hinges that fit. These are 21"X45" vinyl windows. The part that mounts to the frame is 9 1/2" by 3/4" and the rod is about 6 1/2". They don't have the lock that is on yours but there is an adjustment nut under it. Maybe exact lengths aren't needed. I didn't see any manuf ... (cont.)

Please identify part and price.

The bracket that screws into the bottom of the vinyl casement window and provides the sliding pivot point for the window has rusted in half. There is another pivot arm that comes off the same bottom bracket that attaches to the other part of the sliding mechanism. The crank handle that matches all ... (cont.)

Hello Swisco,The Glass Guru of Carlsbad here. We need several of these for a customer, but we're going to start with one to try. EntryGuard by Truth, 4" straight arm, 9" long arm, 3 1/4" crooked arem, 5" bottom straight connector. Right side, including track on bottom of window.Can you find this, ... (cont.)

need bottom hinge plate for 4 windows

Need to replace this hinge. Truth 30744. Ordered 36-004-10 thought this would work. It did in one of my other windows but not on this one. What do I need?