Viewing all customer Discussions for:

33-016 #8 x 1" SS Installation Screw

Hello,I need help finding this window balance. If you need additional pictures or information, please let me know.Thank you in advance.

I need a left and right l, I am not sure which one I need. If you could help I would appreciate it. Thank you!

Hello, I am in need of helping identifying the replacement right and left tilt latches and pivot shoes for my single hung tilt vinyl windows. The existing tilt latches match the dimensions of part 26-244 but the design of my latches are different. Pictures below. Also, for the pivot shoe, these ... (cont.)

I am looking for Hurd window arm operator replacements. I have attached some pictures of one. On the one you can make out most of what I am hoping is a part number. Needing to know what part number I need to order as well as how much it would cost. Looking to replace 4 Right (when looking at it from ... (cont.)

Attached are a set of picts showing spring compression blances for our windows. We have no idea who the manufacturer was ans need to replace the blances for all 10 of these windows. Only one works today. Springs are covered by a vinyl tube as seen in some of the pictures. One picture shows a spring ... (cont.)

Good afternoon, I am working on my windows. I need to get this part for four of my windows. I am not sure which one I need. I have attached a few pictures. Please let me know if you need any other questions. Thanks so much.

I need one spiral spring balance: 26" long x 9/16" diameter tube Also need 26" brush weatherstripping: 3/16" plastic width and 3/16" overall height.

See the attached photo but I want an arm that's only 6 inches long. This is for a casement window. I am replacing a device that is for a smaller but identical window to the part that I sent you. Here's the window that is missing the part a previous homeowner lost the lever. It is identical to the c ... (cont.)

Do you have a replacement for this handle?

I'm searching for the 2 parts seen here framing the locking mechanism, not the actual lock. I'm not sure if it's the same part twice (inside and outside) or I'd they are two different parts. Interlock Bracket operating/meeting stile

Hi there - I am hoping to convert these double-hung wooden window sashes from spring balances to spiral balances. The sashes are 43"x43" and weigh around 20lbs each. Currently they have spring balances and aluminum jamb tracks. I want to ideally keep the aluminum jambs and install the spiral tubes ... (cont.)

Hello, I would love some help in identifying some suitable replacements for quite a few spiral balances. These are for some large windows in a school building. These all have balances for both top and bottom sashes. The original balances have flimsy plastic sleeves that have broken on numerous windo ... (cont.)

Have a tilt window with broken spiral balance on right side. Various connecting pieces broken both sides and on the window itself. I can identify the pictures if needed. I had 10 pictures. Hoping to sent the rest in 2nd message.

Good morning, I just want to verify that 39-253LB is correct. Also do I need the replacement black retainer for the end of the long arm? How about new window bracket at end of short arm...mine has a stud with a slip ring. Thank you.

What parts do I need here?

this piece in the window is what holds the 30" Series 600 Spiral Tilt with the screw

It's for tilt windows, I see markings of 26-5, TB and BSIN. These balancers have 3 solid sides with a spring on the open side. Cord screws in on top and these go inside the channel....I am unsure of the ends of balancer, I see a plastic piece that is in the window channel and sent you a picture. T ... (cont.)

I have some spiral balances which consist of two different lengths everything else is the same they are 25 and 29 inches in length and 3/8 inches in diameter. The other white piece is 1inch in width, 1 7/8 inches in length and 3/8 inches thick. Also I'm attaching a picture of the screw that holds th ... (cont.)

For Florida extruders windows. Also besides the channel I need the vinyl parts to hide the channel the sun has turned them very brittle. Do you have such parts?

I purchased a home that has original MW Twinseal single hung windows throughout from 2000. Almost all of them have broken window balances. I have measured the silver tube (27" x 3/8" diameter)and the black foot (1 1/4"). After studying your website and comments, etc. I think I need the 850 series ... (cont.)