Viewing all customer Discussions for:

39-504 SS 13-3/4" Channel Guide

I am looking for brass window cranks for a home built in 1930 with a large number of leaded glass windows which I believe were by Getty of Philadelphia. Attached are pictures. The base of the crank is around 6/16 or 7/17 wide. Some of the groves are worn a bit thin so it will vary. ... (cont.)

Length of arm is 9 1/2 inches. Length of track is 13 3/4 inches.

Hello, I have attached photos with measurements on some parts that broke on my window. Please let me know if this is adequate information to see what the new part is. I am sorry that I did not send pictures of it installed, I found this option after I already removed it. I also found what I believe ... (cont.)

A. Photos show a LEFT hand operator (I'll probably need a RIGHT hand, also).B. Note the tip "glide" point on the arm is a "DISC'", not the more common rectangular "SHOE".C. No other markings or identifiers on the window frame, glass, etc. (really? couldn't stamp a Model# next to your company name ... (cont.)

Looking for a casement window operator. Looks like a Detroit 2320. Is this still available or is there something that will work? Thanks

Attached are photos of an Anderson 7073B R operator and 7047R latch. Appears the consensus is to use the Swisco 39-365/6 to replace the operator. Suggestions reg. the latch please? Needs to be in white finish ideally. Thank you.

My question is can I remove the complete setup of the 7073B including the rail on the window and replace it all with something comparable??

hi, I found your site while looking for hardware to replace Andersen window casings 7030A (2) and B. The 'genuine' Anderson parts are $150+ each. Way too much... I saw a thread where someone recommended the 39-094. Later someone posted that they installed this, but they had to do a lot of work shavi ... (cont.)

NEED A REPLACEMENT MECHANISM FOR LEFT WINDOW. DO YOU HAVE ANY LITERATURE THAT MIGHT HELP ME DECIDE THE CORRECT MODEL? hAVE LOOKED ALL OVER THE WINDOW FOR A STICKER OR NUMBER, TO NO AVAIL. IS THE ONLY WAY FOR YOU TO SUPPLY THE CORRECT PART TO HAVE ME SEND PICTURES? tHANK YOU IN ADVANCE FOR YOUR HELP. ... (cont.)

I am looking for Extra Heavy Duty Crank and Rail to replace the existing crank for steel window which is very old and very stuck. We replaced the original cranks with the ones you see in the photos, however most of them were broken because it is not strong to open heavy window especially when start ... (cont.)

Hello, My contractor threw out my original cranks and so i'm looking for replacements. I don't have any of the original parts but I do have these pictures. Can you help identify/source replacement cranks? ~Paula

The window does not crank open as the rod with the plastic ball on the end continually pops out of the track on the window Wondering which replacement part we need? Thanks!

These are 12.5" long and are a track for a crank window. I need 6. Do you have them in stock or can you order them? Thank you, Tracie

Do you have rivets available to install the operator tracks? Existing rivets appear to be about 1/4 inch hole, 3/16 head, 1/8 grip.

Operators: 40066 and 40065 Channel guide DIMS: holes are 12" OC 12-11/16 overall length 21/32" overall width 3/16" thickness

I am trying to find replacement operators to replace several operators that no longer work. The attached pictures are of an original operator. Which side are the hinges on for each hand? I will need both right and left hand operators.The property was built about 1950. The windows are inset in the ... (cont.)

Hopping to identify manufacture of my windows and their approximate age. Need replacement parts for cranks and crank box. I was also seeking opinions if I should just replace them even though none of the double pane windows have lost their seals. They're are approximately 20 windows in the house. ... (cont.)

Hi, these cranks are in a New Orleans church building; construction probably dating to the 20's?. They are brass and a bit different than similarly sized current ones, both by having a rectangular brass slider held in place on the arm by a short screw as well as a centrally located crank. Exact re ... (cont.)

We are doing a large restoration job in VA and will need to replace several, several awning cranks. The attached pics are an example of a typical crank that will be replaced. Please contact me with any questions or if you need more info.

Hi, I'm trying to close this window. (See attached pictures). There are two issues: the crank shaft which should have splines is worn flat. There's nothing to grip on to In order to turn the crank shaft. In addition, the operator was likely damaged by burglars who pried the window open from outsi ... (cont.)