Viewing all customer Discussions for:

75-006 Spiral Balance Charging Tool for Tilt Windows

This is a picture of the two balancers I took out of my tilt window.After measuring I came up with a 27 and1/2 inch tube and 28 and 1/2 spiral.The dimensions of the glass is 26 1/4 x 30 1/2 and weighs 18 lbs.The diameter of the tube is 3/8 inch.It also has a blue end which you should be able to see ... (cont.)

I need replacement Patriot window parts. Can you recommend which ones i need. if you need additional infomation, please let me know.I need the Piviot Shoe and Upper sash Slide latch.I recently purchased several other window products from Swisco and while installing them, i noticed that these partswe ... (cont.)

My windows will not stay up. Do I only need to recharge the mechanism or should I replace the old ones? The windows are several years old. Video was very informative. Thank you.

Good Day, I have a spiral tilt balance shoe that I am unable to match. I saw a similar one on line that you matched up and I have attached a picture with writing that is mine. I hope you will be able to tell me what part this is.Thank youCathy

Shoe measurements: Lenght: 2 1/4 inches Width: 1 1/4 inches Height: 9/16 inches Grove devuce lenth: 1 1/16 inches Grove device width: 1 inch Grove device raised appendage heigth: 1/4 inch Grove device raised appendage width: 1/4 inch

I have a tilt in 3x5 window which has a lower sash which weighs 17 lbs. The spiral balance has a plastic tube and its length is 29" and a diameter of 7/16". The metal portion extending from the bottom of the tube when fully retracted has an extended length of 1" and has two pins which are 7/16" fr ... (cont.)

Can you tell from the attached photos which pivot shoe I need Thanks Scott

I'm looking to replace these parts on several windows. They are an older style and are still working well other than some wear and tear on these parts. Any help in locating these replacement parts or a suitable upgrade part would be appreciated.

No markings or labels on the window itself. It appears the shoe is 1" wide x 7/16 deep x 2" tall. Thanks in advance.

Our mountaintop inn has aluminum spiral balance windows. The shoes are breaking and we can't find their replacements. We have a few shoes that look very much like Swisco's 15-045 and 15-212. However, the 3/8" thickness of those shoes is just a little bit too thick. The windows are too stiff for our ... (cont.)

Window parts needed

I am looking for the correct pivot shoe. It appears I ordered the wrong ones. I need the pivot shoe that corresponds with 29" Series 600 Spiral Tilt Window Balance, Product Code: S600-29. I have attached a picture of the one I pulled out of the window.

Window Series# 1400 Superseded by #660 Window ID #00752517 Referred to as a Balance Shoe or Pivot Lock Shoe Part # 6602BAL SHOE/00000 (000011100)

Can you identify my pivot shoe Thanks

Hello, So glad I found your site... Almost all of my windows wont stay up and its very frustrating. These old spiral balances are so gone if I pull any tension on them the mechanism slips and the metal spiral easily pulls down.. Think its time to replace. I believe I need the 27" spiral 600 series ... (cont.)

I need the spring bars for windows. 10 31" red tip 10 29" red tip 20 pivot shoes 17/32" And the tool to install them. I tried to call but no one answered. Can you guys please help?

The cylinders are blue tipped. Do you have these slider parts. I need (4) or the parts and the cylinders

20 1/2" length Dark blue tip The end with the screw appears to be flat. The whole part had a plastic cover which became old and fell off.

What can be used in place of these original pieces?

Tried to wind spring but will not stay in bracket. Do we need a new spring or piece that holds spring since Window keeps falling down?