Viewing all customer Discussions for:

16-002 Take Out Clip

Ordered other ones, didn't know one window was smaller! Pics attached-length of metal part is 15 15/16" ((just shy of 16"). Sash weight is 22.2lbs. Only need two (one window set). Also would like 6 window take-out clips (a couple broke). Thank you.

I need 12 - 1/2" x 24" (Metal) Channel balance #2320, with 10 Take-out clips

Side load single hung balance springThe metal part is 32 1/8" long. It has a 31 3 HW CMC 7 printed on itThe spring end has a plastic tip that is 1 5/8" long held in with a rivetThe bottom plastic piece is 1" longWhich Swisco balance spring would be a direct replacement for my unit?Thanks,Bill ... (cont.)

The broken one is original. The white one is willing to replace a couple years ago. Can you recommend the right part to repair it is thank you. Also, do you sell the little metal clips that hold the guide in place by you repair the window

I have4 balances that are bad. They are all identical. Number on the balance is 36 4. I included a photo of the number.I am not sure if the takeout clip is included, but I am missing two and would like 4 when I install the balance.I purchased a balance from you February 2022. Your video's showed how ... (cont.)

There are two major markings the first being the series 9000 SH on the windows. And the second being 86 27-4 GMS CMC 87

i have a 30 inch channel balance, bottom width 9/16, depth is 5/8, marking is 29 4, but the 2 is barely visible, with letters BSI. Both the top and bottom guides have wings, bottom guide is 1 and 1/16 wide on its side, 7/8 wide on pulley side. This is brown. The top guide is 5/8 on its side and 7/8 ... (cont.)

Hello, Need help identifying which part I should buy.

Near the top of the balance is engraved 28B From plastic tip to plastic tip it measures about 30" Just the metal measures 29" From the sill to the top of the window (Only the moving sliding window) Measures 30-31"

We need two of these

Hi, I am looking for replacement parts for 2 windows the same size (H-LC30-53x96)>I need partsTake out Clips (right and left side)Side load channel balance (right and left side)Top sash guides (right and left side)Length of side load channel balance is 30inchesThe marked writing on side load chan ... (cont.)

Hi, I'm hoping to get help identifying the appropriate replacement channel balances for two windows. I've attached a set of photos of one of the channel balances. As seen in the photos, there is a stamp on it, 2740. I measured the length at 28". I will need four identical channel balances in all a ... (cont.)

I measure 31 5/8" Stamp - 31 5 Milgard Window I would need a total of 6 balances

Hi, I have a series 395 26" window sash. I just need one replacement sash but I also noticed that there is nothing on my window to actually grab on to the sash. I am not sure what parts I need on the window so it may grab on the sash. Thank you.

I believe this is a "28" Series 395 Channel Balance (Product Code: S395-28; Option: 2740)" per the attached images. I only pulled one side (the broken one), but am planning on replacing both (and then have a well used spare). This balance appeared to have lost the window frame clip as I couldn't ... (cont.)

Please provide Swisco replacement part number for this window balance. Thank you!Jeff

28-4 BA CMC and either 11-1 or 1-1 (I can not make out the final section). Width is a half an inch. I have trying to find out what channel balance to replace my existing ones with.

Hello:Do you have the replacement for this hook? I need a couple.Thanks

There are no names, numbers or markings on existing balancer. Metal to metal length is 29 inches. Photo of the window attached so you can see where the balancer goes. It's a single hung window with W X H dimensions of 35.5" x 32" for each sash (or 35.5" x 64" for the entire window) Can you please h ... (cont.)

please help me identify these parts.