Viewing all customer Discussions for:

95-031 Square Cut Corner, White

Measurements are written on an old piece. Used a caliper. 3/4" block, 1/4" wide, 1/2" wide on side. I think I've located the correct one on your site but want to confirm.

Am looking for corner key for window screen frame, etc for the above piece. These are 5/16 inch thickness. Please see pictures - Thanks! Lori

Do you have the SilverLine screen parts in the pictures. The corner pieces with the pull tabs are labeled 842-2A, 2B, 2C, 3D. Need both sides of this part and also both sides of the bottom corner pieces. (See IMG_4391.Let me know if you carry the replacement parts and I will let you know the quantit ... (cont.)

Do you carry a corner like the 95-186 and 95-187 that would better fit a .170 spline. Thanks, Joe

Hi, The screen corners measure> 9/16'' wide X 5/16'' thick X 1'' Long----------- The Bottom Sweep is 1/3-8''wide and has 2 plastic channels that slide into bottom of door. Please research for me ok? Thanks >>>>> Rob

Need white screen corners see attached photos. I.S. demensions 1/4×3/8. 1/2 to slot. O.S. demensions 11/32 x 3/4.

the picture is of a Stanley window screen upper corner insert with pull and latch. The number 842-2A is stamped on the latch tab that slides up and down. I am also looking for the bottom corner inserts w/o the pull or latch. The rolled screen frame is 3/4" wide X 5/16" thick.

Hi Need replacement for part like on the photos, the corner is 3/4 x 3/4, 5/16 thickness. Thank for finding which one I need Eric

Searching for replacement screen parts (see photo) Window is milstone single hung series 1000. Are they still available. The screen channel is 1/4 x 3/4 white aluminum. Original windows have Fl. Extruders Int. label.

how wide is the part that slides into the frames to hold the corner key in place? Also, the measurements I have are 1" by 1/4" with the key length of 3/32

I purchased 95-263 and 95-262 to make up some screen frames. I thought they fit into a 5/16 frame but it seems that they're sloppy. In the picture with the three corners the plastic corner that is not yours does fit snug. Did I buy the wrong ones? Is there a specific frame to go with these? (I'd rat ... (cont.)

My screens need a 1" Screen corner and no one seems to have them. Do You?

I'm looking for this screen corner. The dimensions resemble your part number 95-031, however, I'm concerned about the 1/4" area that I have highlighted. Thoughts?

Can you help identify this screen corner? Thanks.

My existing key corners disintegrated when I removed the screen. T

Hi, the top part of the corner goes into a standard 3/4" screen frame that has a 1/4" thick opening. The bottom part of the corner goes into a different size frame. The best way for me to describe the bottom part is that the frame has an opening of 3/16" by slightly larger than 1/2". ... (cont.)

Having trouble finding this on your site.

This is a screen corner that measures 1.75" overall. The corner block is .75" long and is right between 5/16 and 3/8 thick. It won't let me upload photos for some reason.

Hello Swisco I'm having a bear of a time finding internal corners to fit my screen frame. Most recently I tried Swisco 95-013M, the ½" x 3/16". They don't fit into the frame of the aluminum screen that I have. I have already tried the 95-012M and those were way too big. So my question is ? do ... (cont.)

I have 20 year old screens and the corner pieces are getting worn and breaking. Can't find this piece on your web site. I thought I had the right part (piece on left side in picture) but it does not have the edge like the old piece. Bought new pieces from your site (part number 95-112) but will n ... (cont.)