Viewing all customer Discussions for:

18-009 5/8" Top Sash Guide

Looking to get replacement glides for my windows.

I just received the correct b&t balance, thank you but discovered a broken top ash guide. It is 1 1/2" long, 9/16 deep, & 5/8" wide. I didn't find an exact match in your site but if it can be special ordered or a top sash that will work if possible. Thank you for the help

Hello, We just want to make sure we are ordering the right replacement piece

here are the photos of the balancers and sizes that i am looking for. if you can send me a qoute on these items in the pictures. Thank you. All Balances are for Non-Tilt Windows. The Width of the Channel Balances are 9/16 on the Stamp side, which is equal to 1/2".

Hi Looking for the part number of this part. Thanks

The white plastic tab shown in the photo is broken. It screws inside the channel at the edge of the vinyl sash frame near the top. Not sure what it does.

Require assistance in identifying channel balance and sash guide parts for Milgard Window. I looked on all sides, including inside the channel balance and could not find any markings or numbers that would help identify the part. Other smaller Milgard windows in the home have channel balances with ... (cont.)

Hey there, I'm kinda stumped here. I can most likely force some of these Top Sash Guides that you have into working. However, I'd prefer to have an exact match if such a fabled piece exists.

Hello, I searched your site looking for top sash guides for my broken window. I purchased two S385-26 parts not knowing that my top sash guide was also broken. I found part number 18-008 and 18-008H but mine are much smaller then those height wise. Mine are 1 3/8 inches long and the screw hole is ... (cont.)

Hi,Need to purchase 6 x : 17 5 AT Caldwell2 x 24-14 LF5 CMC 54extra brackets that they hook into on window,see photo'sMuch obliged.Andre

I'm looking to replace a Milgard window balancer that is stamped 26-4 HA2 CMC 24. 1/2 INCH channel.

Hello! I have looked through all of your window parts and couldn't find this one. I am sending a photo of the broken one and the other functioning one. Can you help us id it? Thanks!

I need to confirm the part. Seems the right and left side are different. One side is 3140 and other is 3140x. Both are 32 inches.

I don't see this on your website. 5/8" wide, 7/8" from the top to the center of the bottom screw hole. 1/16" to the upper screw slot.

Hello, I'm looking to replace a broken block and tackle window balance. I found your site by googling PAT #6598264. The stamped marking on the metal is 25 4 and the metal rod measures 25 5/8".

Hello Experts, I want to replace my Top Sash Guides on 6 of my house windows. The dimension matches that of "18-009" on your website except for the height. Your product "18-009" has height of 1 11/32 inches whereas mine is 1 9/10inches. Rest all the dimensions are spot on. Do you have a top sash g ... (cont.)

Could you kindly let me know the part number and cost for the window channel balance replacement part as described in the 5 attached photos?Length (metal end to metal end): 33"End width (plastic part): (1 +1/16)"Part info printed on original window balance: 32 5 DV CMC 7Thank you very much!Qiang ... (cont.)

Hello, I need help replacing these parts, can you identify them and help me please? the Metal measures 25".

I have this 5/8 x 1-7/16 sash guide for an unknown brand single hung window Any help?

I'm looking for four 5/8 sash guides as pictured. The top is 7/8 and the drop to the screw hole is 3/4 from under the top.