Viewing all customer Discussions for:

19-002 Channel Balance Top Guide

Hello, I have not been able to identify the particular channel balance combination needed on your website. The top guide appears to be similar to the 19-002 model, but I have not found the correct bottom guide. Please refer to the attached images and the approximate measurements below. Metal ... (cont.)

Db lo2 2330 are the numbers on the channel balance. The dimensions are 1/2" by 24" code on channel balance is 2330

I'm replacing a non tilt block and tackle window balance from a single hung Milgard window. I'm not sure this is the original balance. The metal is 33 inches long and 1/2 inch wide. It is stamped 3240. Images of the ends are attached. I'm thinking of ordering the 33" Series 351 Channel Balance, S3 ... (cont.)

Hello! Trying to determine what replacement part(s) to order from your website. The part is stamped with

Hi, I need to replace the channel balances in a whole house. However, I don't know which ones I need. It is labeled 940, has the 19-002 type top & the 15-003 bottom 21". Please help!

I am trying to identify the channel sash top stop. The aluminum is stamped 2720, the shoe I think is 15-002, the top I am having trouble with. It has a V shape that none of the options have. Can you offer a substitute and can you send a sample?

I am looking to replace the channel balances on 9 identical non-tilt windows and would like to know, what determines the 'series' of channel balance to use? My balances are of the 1/2" (9/16") variety, are 29" long, and look to have the 15-003 shoe and 19-002 guide. Thank you for your help and time ... (cont.)

34 w x 36 h edge to edge of metal frame for removable bottom, double pane, single hung window first two photos are bottom guide

I need to order two different block and tackle glances for a few windows. Here is what I can find on the parts: First set: Lettering on the unit 30 9 BR CAELDWELL, Length 31", Width 1/2 " see pictures attached. I need four of them Second set: Lettering on the back 20 E 15, Length 29", Width 1/ ... (cont.)

I need two balances for a non-tilt window. The balance looks like the 351 series but doesn't come in 11". The top shoe looks like a 19-002 and the bottom is a 15-002, It has 1020 stamped on the shaft. Can this be custom ordered and what is the cost? I have attached three pictures Thanks ... (cont.)

Trying to repair a couple ancient Nuprime windows in my father's old house, where the channel pieces have decomposed. The channel itself is a 1/2" w aluminum channel which is stamped "3030). The top sash guide (now broken) is stamped "3031". Having trolled your website, I believe that the Top sas ... (cont.)

Hi, I'm having trouble finding the replacement parts for my sash window balance. The balance is 1/2'' wide. I would also need to purchase the shoes, top, and sash guide. Hopefully the shoes and top are standard replacement, the sash guide is very difficult to identify, so I've included some photo ... (cont.)

Hello, I would like to replace the two channel balances in a sash window. I have attached pictures of the existing balance. The metal part is 28" long (excluding the plastic end caps) and is stamped "2730". The window is an aluminum frame, original install in a house built in 1986 in California. ... (cont.)

Just want to be sure that I have the right top/bottom pieces on my 33" long 1/2" channel balance. Looking at your website, I'm guessing that the top is a 19-002, and the bottom shoe is a 15-002. Since it's a 34 pound window, I'll spec it as a 3260. Please confirm. Thanks.

Would you please tell me if you have these balance parts for a old Kinko window? In closed are pictures of the end fittings and the ensemble part I need. The channel is 25 inches long 1/2 inch wide. The stamping on the channel is 2430 AD B.S.I. It appears to me that the end fittings are 19-002 1 ... (cont.)

Good afternoon i'm in the process of replacing a milgard window channel balance. the part is stamped with the following: 32 9 aw cmc 2 the balance is measured 33 inches long 1/2 inch can you advise on the replacement part --- i believe it is 33" series 380 channel balance option 3260 ... (cont.)

Attached pdf file indicates the attachments, 27 in length, window weight of 17.6 lbs, and manufacturer markings. Per your website, I think I need to order the series 390, 27 in length, 19-002 top, 15-001 bottom, and weight range for 2630. Can you verify this before ordering this window balance? T ... (cont.)

I need to replace a channel balance for a non-tilt window. I think I need either a series 350 or series 385, but I don't know the difference between 19-002 top piece and 19-005 top piece. The balance I need need to replace is marked 26 4 JR -- it is 1/2" wide and 27" long A couple ... (cont.)

I have a wooden sash, double hung, non-tilting window with a bad channel balance. The part is stamped with "20 4 FS CALDWELL". Size of the metal channel (not including plastic top/shoe) is 5/8" x 21". Weight of the sash is 18 pounds. Top matches Swisco 19-002 Shoe matches Swisco 15-003 I d ... (cont.)

Hello, I need replacement parts for my jordan non tilt out windows. The channel balance is 29in and I believe balance top is 19-002 and bottom is 15-001 if correct it needs the 29"series 390. I do not know the strength or stamp option that my channel balance should be. The old balance has "28C" stam ... (cont.)