Viewing all customer Discussions for:

S380-27 27" Series 380 Channel Balance

Hi, Jim.Your balance looks like it could be a match for our S380-27 or S385-27, depending on the bottom shoe depth. The Series 380 has a 1" deep shoe and the Series 385 has a 1-3/32" deep shoe. Measure as shown below to determine the best fit. You will also need the 2640 strength option. ... (cont.)

Hi, I'm looking for some parts for some old Alpine window (probably installed in the 90's). Just the metal part of the bar is 27inches long and about 1/2 inch wide (on the side facing the window). attached are photos of the part, and I found a tag (in smaller window as there are none left in the ... (cont.)

Number 2630 stamped. Also stamped smaller is BSI. These balances are over 20 years old.

I just send the pic front & backside pic . Please send me . Or call me please I can replace the order .

Morning. I have multiple balances that need to be replaced and was wondering if you could help me? I believe I have a S380 due to the lower shoe size. S380-based on shoe although similar to S385 ? 27" long ? 1" shoe ? 2640-19 to 26lbs identified on balance

I need replacement balancers for Milgard windows. Photos of the original attached. They are 1/2 inch wide and 27 inch long, excluding the plastic ends. The sliding window weighs 19 pounds. They are stamped "26 4 EW CMC 10".

27 inches from metal to metal ends

I have a window that uses the 27" Series 380 Channel Balance (option 2640). The channel believe is fine, but the plastic part on top of the window (see attached picture) is cracked/broken. There are no markings on it. Can you help me identify the part? The entire piece is approximately 1.5 in long a ... (cont.)

Sliding window, channel balance, 27". Markings on side: 2620, BSI NA Plastic guide with wings Depth of channel 5/8" With of channel. 9/16"

I need a couple of balances for a modular home, KIMRO appears to be the brand of window. Attached are pictures of the balance, I hope they are sufficient. Thanks, Tim

I had purchased some sash in 2019 and one of them ended up snapping today. I wanted to order a replacement and wanted some help picking the right one. The balances did feel a bit tight and I'm always worried it will snap and I'll end up banging the window shut with all the force I need to apply. I ... (cont.)

27" long

House built in 2003. Might as well replace both balances. Plastic "ear" broke off on right-side balance. BSI 2630. Please advise of price for the balances and shipping to 80020. Thanks! Ed

balance is 27", window is 30lbs, marking on balance 26D please let me know what to order. I need 2.

Hi, I have watched a youtube video from buck4mt about replacing channel balances for Milgard windows, which is what I have. My balance is 1/2" wide and 27" long (metal only). The top and bottoms look like the 380 series. My question is about the strength. The stamp on the side is "26 4 FV CMC ... (cont.)

Looking for replacement part for a single hung window. The sash spring is broken so I would like to verify the correct replacement part. The aluminum channel is 27". I'm guessing it is part number is 27" Series 385 Channel Balance Product Code: S385-27 Option 2630? Thanks Trent

Hello! The balancers in my windows are pretty worn down. I am looking to replace them and wanting to be sure I order the correct part. I would appreciate help pointing me in the right direction. Thank you!

Metal channel is 33in. Stamp is 3240. 20 years old.

I need 12 of the 26 3 do codwell and I need 6 of those 20 3 DK codwell and I need 12 plastic holdersKevin

Hello, I'm looking for replacement for these channel balance parts. The metal channel is 27" long and ~5/8" wide. The metal channel is stamped with the following: 26-3 HD5 CMC 54. Thanks! Joe