Viewing all customer Discussions for:

S380-29 29" Series 380 Channel Balance

Photo of broken window sash and working window is attached. label of manufacturer is attached.

I need to replace 4 window balances. They are marked 2830 and also 28C. The length of the metal channel is 29". The width of the channel is 1/2". Each sash weighs 19 lbs. The top shoe appears to be a 19-005. The bottom shoe appears to be A 7/8" winged channel balance shoe #15-029. Photos are attac ... (cont.)

Greetings, I just pulled this 1/2 inch channel from my window, I need your help in getting the right channel. Also please let me know, if you need any additional information. Appreciate your help.

Hi,Ja-Ni in customer service told me to contact you to order custom window balances after I sent her the following email:Hi Ja-ni,I measure the front to back length of the lower shoe to be 7/8". The diagram from Florida Extruders says that it's actually 29/32". SWISCO lists a part #15-029 that is 7/ ... (cont.)

Wish to order 4 window balances as shown in photos. Length not including plastic parts is 29". Thank you. I have ordered parts from you in the past. Very satisfied with your product and service. Kevin Kelly

Hi, I have a 29" track marked 28B. I purchased replacements (not from you) but the channel is too deep. I think by 1/16" maybe. When I say channel I mean the metal 29" track. Do you have this? I need at least 4. Thanks, Dominick

1/2" Wide Channel Balances , the metal is 29" long, see a # 2830

Metal shafts are 29 inches and stamped 28D. The window is larger than standard single-pane window.

They are 1/2" balance tubes, but have a longer top end catch than i have seen. See pictures. The height of the foot end is rather small at about 13/16". Please help. Thanks

I need to order (6) window channel balances. The length is 29". The ID # on the channel is 28 4 BSI. Please advise which part I should order. Thank you, Brett

Windows are approximately 26lbs each. Only identifier is 28D. Windows from 2006. Metal channel .5"×29".

I need to replace channel balance on my window, what model do I need it? Thank you.

Hi can you please advise on the correct balance shafts i need, Length is 29' width 9/16, markings on shaft are hard to see looks like 28C Thanks Tony

Hi and thanks in advance for your help. I just bought a home in FL, and two windows (same size) need new sash balancers. The windows are heavy/ hurricane grade, about 32" wide by 50" high (each pane), non-tilt. Metal is 29" long, nearly 5/8" width, and 1/2" depth. The only stamp is 28G so I don't ... (cont.)

I'd like to replace the balances in a few of my windows. They have 28D stamped on them. Thank you for your help!

Specs:text printed on existing balance: 28 3 GW cmc 11length: 29"width: 9/16shoe width: 1"supported window panel (approx): 34" X 32". No tilt.Not sure of the weight range.Photos attached.Is SERIES 380 the right channel balance for my window? Which Stamp Option should I select?Respectfully, Amit ... (cont.)

Trying to find out what balance I need for my windows

my part needed is for a non tilt out window balance. The metal is 29" inches long and 1/2inch wide. I was looking at the s380 and s385 but not sure which on I have. The metal has 28B stamped into it. Please advise which windows balance I need to fix my windows.

Need left and right side. Marked with 28D. 29" long metal frame Vintage 2006

Hi, I need to replace these channel guides. Its hard to see in the pic but the number on it is 286 with backwards 'C' The metal portion of the piece measures 29". It is 1/2 inch wide Would you have a replacement for these? Thanks