Viewing all customer Discussions for:

S380-33 33" Series 380 Channel Balance

32 5 AV CMC 2 33" inch channel with the above markings I need to replace them. Thank you for your help!

I need 4 balances for 2 windows of the same size. steel part is 9/16 wide, 5/8 deep. Windows weigh just under 25lbs. I need complete balance part with plastic ends, strings and clips. The part stamped is 3290ca36.Thanks for your HelpMark

Dear Sir / Madam,I require 4 Replacement Counterbalances. I have attached photos.The Number Stamped on the side is: 32 5 GV CMC 2The Lower shoe appears to have a wing etc and therefore I am assuming that I would require 32" (length of steel) and that the replacement model number would be a 3 ... (cont.)

This window is hard to raise and lower. It looks like a piece of the fitting from the bottom fitting is missing. I would like to get a new set of balances. The window would be 20 years old, not sure of brand and don't see anything on the window

trying to match the channel window balance 33" 32-5 AA CMC 7

I need to replace two balancers for a single hung Milgard window. Balancer is stamped with 32 3 IT CMC 0 although the metal piece is 33" in length. I'm unable to find an exact match to these numbers. Our home was built in the 2001/2002 timeframe. FYI, the forth photo shows one balancer installed, ( ... (cont.)

Two have 3240 stamped on them (33" long), and two others have 2640 stamped on them (27" long)They are all 1/2" wide.I need to order 6 of each.

Single hung Milgard vinyl window - 35"x71" Marks on existing hardware - 32 4 F0 Caldwell

I need replacement for Single hung window balance. The balance is stamped as "32 6 JP CALDWELL". I have attached the photos. I need two of these. Please help me identify part number. Thanks.

32 4 HQ Caldwell. 1/2 inch wide

Hi I have a Caldwell channel balance which is 33" long. It has a stamping of 32 5 FQ. What should I order?

Attached are a few photos of the window slides from my window. The strings were broken and the springs missing. Four photos are of the slides themselves, and the fifth photo is of the markings in the window itself. I'm not sure which manufacturer. Thanks!

Hi, one of the channel balances on my sliding window need to be replaced. The cable has broken off. Looks like the width is 1/2 inch. There's a print that says "32 4 DV CMC 7" on the rod. Thanks

The stamp on my channel reads "32 5 JV CMC 2" I know I need a 33" series 380 but I'm unsure of what the stamp means as far as sash weight range. Thank you for the help!! :)

I am seeking the proper part number to replace the channel balance hardware in a single hung window. I have attached photos photos of parts of the existing channel balance hardware, one of which includes the product identification number. I have also measured the metal channel only for length and ... (cont.)

Milgard windows installed in 1998. Please identify channel balance-33" with marking 32 3 CQ CALDWELL

Greetings, I am looking for the channel balance replacement for our window. I was able to get as far as... Channel Balances > Non-Tilt Window > 1/2" Width then the next screen I was not sure what to pick. the silver metal length is 33" exactly. (not including plastic ends). Pictures included. Can ... (cont.)

I am pretty sure I need the 33 inch series 385 channel balance. The only other one that I am considering is the 33 inch series 380 channel balance. Do you think I'm on the right track? I see that the only difference between the two is the depth of the shoe, and I think the one I have is the longe ... (cont.)

The metal channel is 33". The width of the channel is 9/16". The shoe 1-1/8" not 1".Felix

Hi, I believe I have either 385 or 380, however I'm not sure which. The bottom shoe looks like it's just a tad over 1" so I'm leaning towards the 385. Also, it's 33" and the stamping says 32-9 IX CMC 11, can you recommend the correct weight option to pick? Thanks!