Viewing all customer Discussions for:

21-001 Bi-fold Door Pivot Assembly

Hi, I'm looking into restoring these old metal bi-fold closet doors. I was wondering if you had all the hardware needed including the rails. I'll upload some photos.

I don't know the maker of my metal doors, but the label mentions where to write for spare parts. My doors are missing some hardware, so I want to replace all doors with new hardware. My doors each have the three spring guide pins and the one threaded pivot pin. Can I replace them with the 21-001 ... (cont.)

Hello, I need the bottom tracks and track hardware for a bifold metal door. Which items number is it. The width of the door is 30 inches.

I NEED 4 SETS OF THESE GUIDE PINS. MY PHOTOS SHOW ONE FOR BOTTOM AND THE OTHER FOR TOP OF DOOR.CAN YOU PLEASE ADVISE THE COSTS AND WHEN CAN THEY BE SHIPPED. OF COURSE AFTER I PAY. THANK YOU. SORRY THE PHOTOS ARE SIDEWAYS.

These are metal bi-fold doors. I've used in the past parts I got at Lowe's, but, they don't last, they are not the proper parts. The pins are 1/4" and the piece of plastic that rides in the track is 3/8". Can you help?

Do you offer something that could work for this?

Hi, I have a bedroom with metal bi-fold doors that's missing parts & someone tried to use a top pin that's for a wooden door. Currently, the left door is leaning against the wall. I know for sure I need the top pin for the left side & the right side seems fine. I've included pics of each side. I ... (cont.)

Good morning,Would you be able to help me out at getting parts for my doorsI have 4 set of doors that are 4 feet and 1 that is 5 feet.I would like to buy the plastic caps for all of them.the pins look like they are 5/16 and the swivel one are also 5/16 but are smaller at the bottom where the cap goe ... (cont.)

Hello, I am at my wits end with my bifold doors from the 70s. I bought these replacements parts, hoping they would solve the problem, but even though everything fits, the door is still grinding on the track instead of gliding. Is there something I am doing wrong? Attached are photos of the bot ... (cont.)

We have a home built in the '70's. Almost all of the closets have 89" metal, bifold doors. The doors vary in width depending on the closet opening, but all are the same design. Since it would be a messy and costly hassle to reconfigure the closets and the openings to change to a "modern" door design ... (cont.)

Thanks... Happy I was able to find replacement parts. This is the piece I need. Can you tell me if this is something you can sell me?

Hi there! I have some vintage metal bifold doors that need all new hardware. What are your suggestions.

Probably from the 70's. Track is aluminum and close to 3/8 opening for bushing to ride in. The bushing shown must of had a bottom for the 1/4 inch rod or it would float up and down the rod and not stay riding in the track. The rod has a screw you loosen to raise it up and down, which should make it ... (cont.)

hello I am in need for pins for a complete bi-fold door and pivot clamps for them The upper pins I have are the same as 21-065. do you think that the pivot clams 21-154 will work for me

I have an old metal bi-fold door that is missing some parts but in overall good condition. The pivot rod clamp, pictured, I believe matches your part number 21-154. Also, the bottom guide pin, pictured, matches your part number 21-001 and 21-005. Not sure which one is the right one. ... (cont.)

Good Morning! I need to know which will be replacement part for above bi-fold door top and bottom . Thanks

Hi I have a few older metal bifold doors that were installed with the pins and a track on the top and bottom. I'd like to reinstall them with new pins and new track on the top only and use a corner jamb if possible. What parts would replace what I have? The holes in the doors for the pins are 5/16"T ... (cont.)

Trying to redo old bifold doors need all hardware for both sides. Two panels each side (4 total)

Hello, I need to place order fot the closet door parts. I have uploaded the pictures. Please help me identify the correct part part number for me to place the order. Thanks Vik

The line that move in the track have no springs. I have tried tightening the screw below it but the pin keeps popping out of the track. Will replacement hardware keep the doors from popping out? Any help Is greatly appreciated