Viewing all customer Discussions for:

21-154 Pivot Rod Clamp

Good morning,Would you be able to help me out at getting parts for my doorsI have 4 set of doors that are 4 feet and 1 that is 5 feet.I would like to buy the plastic caps for all of them.the pins look like they are 5/16 and the swivel one are also 5/16 but are smaller at the bottom where the cap goe ... (cont.)

We have a home built in the '70's. Almost all of the closets have 89" metal, bifold doors. The doors vary in width depending on the closet opening, but all are the same design. Since it would be a messy and costly hassle to reconfigure the closets and the openings to change to a "modern" door design ... (cont.)

Hi there! I have some vintage metal bifold doors that need all new hardware. What are your suggestions.

Probably from the 70's. Track is aluminum and close to 3/8 opening for bushing to ride in. The bushing shown must of had a bottom for the 1/4 inch rod or it would float up and down the rod and not stay riding in the track. The rod has a screw you loosen to raise it up and down, which should make it ... (cont.)

hello I am in need for pins for a complete bi-fold door and pivot clamps for them The upper pins I have are the same as 21-065. do you think that the pivot clams 21-154 will work for me

I have an old metal bi-fold door that is missing some parts but in overall good condition. The pivot rod clamp, pictured, I believe matches your part number 21-154. Also, the bottom guide pin, pictured, matches your part number 21-001 and 21-005. Not sure which one is the right one. ... (cont.)

Good Morning! I need to know which will be replacement part for above bi-fold door top and bottom . Thanks

Hi I have a few older metal bifold doors that were installed with the pins and a track on the top and bottom. I'd like to reinstall them with new pins and new track on the top only and use a corner jamb if possible. What parts would replace what I have? The holes in the doors for the pins are 5/16"T ... (cont.)

Trying to redo old bifold doors need all hardware for both sides. Two panels each side (4 total)

The line that move in the track have no springs. I have tried tightening the screw below it but the pin keeps popping out of the track. Will replacement hardware keep the doors from popping out? Any help Is greatly appreciated

Metal Bifold Doors, probably original, house built in 1967. Most doors have no markings, but one has instruction sticker. Weldwood Metal Folding Doors, US Plywood Corp, New York. No numbers or model info.

Hi! I have US Plywood metal closet doors throughout our house. We found a set in the rafters and would like to install them back in one of the bedrooms. I have a couple questions, I have the 21-154 (pivot rod clamps) in my cart but I couldn't find the little metal cover parts (see pictures) that are ... (cont.)

Hello, I would like to purchase the pivot pins for my bifold door. Please let me know if you have stock and how to make a purchase.

#2 photo is the intact side. #1 photo show the "stopper?" assembly missing making it impossible to install the door in the upper right runner. There are no readable markings on the door which the builder says is from the late 1960's. Hope you can help. The door is 90 inches tall and 23 inches w ... (cont.)

No numbers seen anywhere on Metal bifold doors. We need complete parts. Our doors are dragging and making grinding sound. No store in town had parts that fit. We watched a video of yours with 21-007. 21-001. 21-154. Will those work? Please help us find replacement parts. Thank you. ... (cont.)

hi, I need parts for this doors. do you have bottomless track?

Hi, Please help me to identify the right pin cap. My pin diameter is 10/32". The bottom diameter of the cap is 12/32" and the length of the cap is 12/32".Please see 3 images attached.From your website I bought pin cap part # 21-100 which has a internal diameter is 1/4" and thought somehow I will be ... (cont.)

4 doors that are 18" each for 6' total closet opening I need the plastic tips on the pins (note that the threaded pin has a smaller dia than the other 3 pins where the tip is installed). I also need the track for the top and the mounting brackets (or track) for the bottom of the door and any addit ... (cont.)

Hi Good Morning,I need Nylon caps for my metal door closet, and need pivot Brackets which are broken.i checked online pictures of the parts, but I want to make sure that I get the right parts. I uploaded the pictures of the nylon cap and and bracket looks identical, but different shape as my bracket ... (cont.)

Missing top and bottom hardware for 2x bifold dodoors