Viewing all customer Discussions for:

21-277 Bifold Track Bumper

We have two closets with metal bifold doors and I am THRILLED to finally be able to fix them. I need new tracks and new pins all around. Attached is a photo of the top pin on one door. Can you help me figure out what I need? Thank you!

I have three metal bifold doors that I would like to reinstall. One door goes in a 36" wide opening and two go into a 72" wide opening. I am looking to purchase the upper tracks and associated pivot mounts, and the lower floor mounted brackets. I do not believe that there was a lower track. If ... (cont.)

I recently purchased a rebuild kit for ~1980s mirrored closet doors. I cannot get the pins to stay in the pin caps as the pins pull out when opening/closing the doors. I reversed the spring tension on the doors(top: push up vs pull down to engage pin) and the pins still will not seat in the cap. ... (cont.)

Dear Sir,We are doing renovation on multiple apartments with older metal bi-fold doors. The hardware for most of the doors needs to be replaced. I have attached pictures of one set of doors and the existing hardware. I do realize that most of the nylon bushings are missing and the pin in picture #14 ... (cont.)

Hi, I'm looking into restoring these old metal bi-fold closet doors. I was wondering if you had all the hardware needed including the rails. I'll upload some photos.

I don't know the maker of my metal doors, but the label mentions where to write for spare parts. My doors are missing some hardware, so I want to replace all doors with new hardware. My doors each have the three spring guide pins and the one threaded pivot pin. Can I replace them with the 21-001 ... (cont.)

Hello, I need the bottom tracks and track hardware for a bifold metal door. Which items number is it. The width of the door is 30 inches.

I NEED 4 SETS OF THESE GUIDE PINS. MY PHOTOS SHOW ONE FOR BOTTOM AND THE OTHER FOR TOP OF DOOR.CAN YOU PLEASE ADVISE THE COSTS AND WHEN CAN THEY BE SHIPPED. OF COURSE AFTER I PAY. THANK YOU. SORRY THE PHOTOS ARE SIDEWAYS.

36" 1 72" 3

These are metal bi-fold doors. I've used in the past parts I got at Lowe's, but, they don't last, they are not the proper parts. The pins are 1/4" and the piece of plastic that rides in the track is 3/8". Can you help?

Hi, I have a bedroom with metal bi-fold doors that's missing parts & someone tried to use a top pin that's for a wooden door. Currently, the left door is leaning against the wall. I know for sure I need the top pin for the left side & the right side seems fine. I've included pics of each side. I ... (cont.)

Metal bifold doors 36" wide by 93" high. Need new track and hardware. I can give more detailed information if you need it.

I have some Leigh Bi-Fold Full-VU Metal Doors Part # 8433. I have one bedroom with the top track still assembled and hanging from the ceiling. I have the bottom piece of wood in place, but need the track that will work with this door along with the parts. The track is right around 4' wide. Do you ... (cont.)

We have a home built in the '70's. Almost all of the closets have 89" metal, bifold doors. The doors vary in width depending on the closet opening, but all are the same design. Since it would be a messy and costly hassle to reconfigure the closets and the openings to change to a "modern" door design ... (cont.)

Probably from the 70's. Track is aluminum and close to 3/8 opening for bushing to ride in. The bushing shown must of had a bottom for the 1/4 inch rod or it would float up and down the rod and not stay riding in the track. The rod has a screw you loosen to raise it up and down, which should make it ... (cont.)

Good day, I purchased this "old"door to repaint and hang. Not sure whatparts are needed. I want all new ones. Can you help? I will be submitting an order for parts on a different type of door but I know what I need for that one.?

Im looking for the spacer or bumper that fit the number on the doorss between the top and bottom of the two bi fold metal doors i found one that looks looks like the ones I have but the length is 2" and the ones I have are about 1 1/4" The door pin cap# 21-108 should fit my track ... (cont.)

I have an old metal bi-fold door that is missing some parts but in overall good condition. The pivot rod clamp, pictured, I believe matches your part number 21-154. Also, the bottom guide pin, pictured, matches your part number 21-001 and 21-005. Not sure which one is the right one. ... (cont.)

Good Morning! I need to know which will be replacement part for above bi-fold door top and bottom . Thanks

Hi I have a few older metal bifold doors that were installed with the pins and a track on the top and bottom. I'd like to reinstall them with new pins and new track on the top only and use a corner jamb if possible. What parts would replace what I have? The holes in the doors for the pins are 5/16"T ... (cont.)