Viewing all customer Discussions for:

15-086 Tandem Coil Housing

We purchased about 20 replacement vinyl windows from Gorell Enterprises in 1995. A few years ago the balances began failing. We currently need to replace at least five of them. I've attached a photo of a lower sash, hoping that you can identify the style for replacement. Please advise.Thanks.Dan ... (cont.)

I believe that I will need the tandem set up using 15-087 and 15-086. The spring has a stamp of 4Y, is this a 4 lb spring? When I install the the two coil housing, I assume that I hook them together and then pull the spring out and run one on top of the other up to the clip. Thanks you. ... (cont.)

Hello. I have this part in the pictures just break on me on anther window. It is the piece of plastic inside the window track to which the actual window latches onto. I am trying to see if this part is sold separately or if i need a new window track or frame. Thank you

I had a window that would only go up so much ( see pictures), when I titled it out I saw the coil had broke. I have removed the coil, but now need to replace it. Thanks!

Please let me know which ones I need

First photo is left balance unit in a window that works. Next 4 photos show right and them left in window that won?t stay open. Seems like there are 2 coils on each side but one on each side is disconnected. On left side there look like a half round metal clip. It is broken off on right side. Windo ... (cont.)

this has a coil spring and as you rotate the window it lock the slide, put the window back in position and the whole assembly moves. Not sure if the slide needs to come out with the window.

The window sash weighs 12 lbs

Could you help identify what replacement will work for me?

The sashes seem to weigh (I only have bathroom scale) about 27 lbs each. I have about 35 of these Gorell sashes with coil balance problem. I?d rather rebuild than replace them. Please let me know what you think. Do you have an installation viideo to help me get the first install done right? Tha ... (cont.)

Had 2 coil balances break on an Anderson window today.It looks like the coils are stamped 5 BD or DD and they measure 15/16" wide.The sash weighs 20 pounds 8 ounces.They look like your series 180 coil balances.Would the 5 pound be the correct one?Would the 15-086 tandem coil housing and the 15-087 c ... (cont.)

I need a replacement balancer and tilt bar with plastic housing. The bar has sheared due to rust and I?m unable to remove it from the shoe.

First two photos are located on the right side of the window and are the broken parts. The third photo is located on the left side of the window is in good condition, and Not Broken. The actual size of the good part is 7 inches height, by 1 inch width. The window itself would not slide up due t ... (cont.)

the window is 44 pounds, vinyl frame. the existing balances appear to be 35/64" deep by 1- 17/64" wide with 3 coils. I inadvertently damaged them while installing the window. Have been unable to contact Crestline. I need 2 pair, plus do you have a spreader tool to remove/install them? Thank you, ... (cont.)

Hi I am trying to replace the pictured part. It has a coil on top and a shoe at that bottom. I think it is all one part. It holds a heavy double hung tilt window up. There was only one coil when I removed. Can you help identify and suggest a replacement part?

I was cleaning my window and (as I've learned later), probably didn't lift my window enough and think I've broken this part. I need to replace it but don't even know what to search. I also can't even get the window back in at this point so it's a bit urgent!

Traco vinyl window 36 x 48Bottom sash weights 22# Need both sides for bottom sash Top spring 6FA Bottom spring 5GA All springs(4), housings, 2 short, 2 long with pivots Thank you Charlie

Please help me locate this part.Pat5,353,548 stamped on side.Two of the tandem housings are marked 7 and end housing is marked 8.I need the coil springs also

Attached are the parts of double hung window manufactured by survivor window

How do u get both springs to hook on to the screw bracket that anchors them? The significant amount of tension in the coil springs appears to make that somewhat difficult? Please explain?