Viewing all customer Discussions for:

15-086 Tandem Coil Housing

First two photos are located on the right side of the window and are the broken parts. The third photo is located on the left side of the window is in good condition, and Not Broken. The actual size of the good part is 7 inches height, by 1 inch width. The window itself would not slide up due t ... (cont.)

the window is 44 pounds, vinyl frame. the existing balances appear to be 35/64" deep by 1- 17/64" wide with 3 coils. I inadvertently damaged them while installing the window. Have been unable to contact Crestline. I need 2 pair, plus do you have a spreader tool to remove/install them? Thank you, ... (cont.)

Hi I am trying to replace the pictured part. It has a coil on top and a shoe at that bottom. I think it is all one part. It holds a heavy double hung tilt window up. There was only one coil when I removed. Can you help identify and suggest a replacement part?

I was cleaning my window and (as I've learned later), probably didn't lift my window enough and think I've broken this part. I need to replace it but don't even know what to search. I also can't even get the window back in at this point so it's a bit urgent!

Traco vinyl window 36 x 48Bottom sash weights 22# Need both sides for bottom sash Top spring 6FA Bottom spring 5GA All springs(4), housings, 2 short, 2 long with pivots Thank you Charlie

Please help me locate this part.Pat5,353,548 stamped on side.Two of the tandem housings are marked 7 and end housing is marked 8.I need the coil springs also

Attached are the parts of double hung window manufactured by survivor window

How do u get both springs to hook on to the screw bracket that anchors them? The significant amount of tension in the coil springs appears to make that somewhat difficult? Please explain?

I need help identifying Traco roller tilt constant force balances for this window. Both top & bottom. I weighed each sash out of the window frame & each sash weighed 21.1 lbs. can u tell me All needed items to put this double hung window back into proper operation.

I'm looking for constant force balance replacement parts This is a double hung window, the windows tilt out and the pivot bar has a notch in the shaft and the shaft has flange like ends (see picture). One spring broken and then a second and then a third. I'd like to know what my options are. ... (cont.)

Bottom Pane spring coil that enables the lower pane to be raised and held in position there are two and I need one for the right hand side since it has uncoiled

Can you help identify replacement parts for the coil balance etc in the attached pictures? Thank you

TRYING TO LOCATE BALANCE PARTS FOR ACCENT WINDOW

Good Evening. I have several Kohler Windows 50979 013 that have broken Pivot bars. The one listed on your site 26-369 looks to be that design but I don't have small enough measuring devise to properly measure it. Would that item be the replacement pivot bar I'm needing from your experience workin ... (cont.)

Greetings!Both the coil balances were discovered to be broken in our ten year old window. Could you help up in determining the proper replacements?Sincerely,Patrick

I'm looking for coil balances for vinyl windows. I've got a bunch of broken ones. The markings on the photo say: CMC 278 35" 7# Also, it looks like there are 2 per window side (i.e. 4 total per window), and it appears 1 would go each of these 2 parts: 15-087 15-086 Finally, no cutouts ... (cont.)

I'm searching for a window balance. it's 2 pieces hooked together. 4 inch length, 1.25 " width, and 9/16 " depth.

I have a double hung tilt window 45" wide x 58" tall. It does not stay open. The coil housing balance looks like it's broken on both sides. what part do I need ? Do you need more information from me to make sure I order the correct part ? Also if you can direct me to a video that shows you how ... (cont.)

Need 2 of this style

I have this blue shoe. Your customer care recommended 15-086 and 15-087, but those have a black cam, and it looks a little different in size. Will this part still work? I already bought the recommended parts and I want to be sure they will fit before I call out a handyman.