Viewing all customer Discussions for:

82-238 Double Hook Mortise Lock

Sliding door handle, says made in new Zealand. Does not have any numbers or other markings other than the squiggles on front. Screw holes where it attaches to door are 4 15/16 inches center to center.

My living room has a 4-panel set of Certainteed sliding doors (Newcastle XT). The two middle panels move, and the two side panels are stationary. The two sliding panels lock in two ways: 1) mortise locks: These locks are doing fine. The left-hand sliding panel is equipped with three mortise locks, t ... (cont.)

My name is Jose I don't know the item # but I need the hole asambly to lock and unlock my patio door thank you

I ordered the Sissco Handle set 82-080 to replace the one I had to destroy to get the faulty mortise lock out. It did not come with a new lock so I ordered the 82-238 double hook mortise lock and neither one was the correct part. Please check the pictures I have sent before sending another mistake ... (cont.)

Please help me identify this! I'm thinking possible 82-238? Want to be sure before I order. Thank you.

I just bought this house with a broken sliding door lock broken.

We have no idea what brand sliding glass door contractor put in and they told us they don't keep records past 10 years.

I'm looking for the correct model latch for my sliding glass door. It's been I've 10 years but I think it might be Metal Industries mfg door.ThanksChuck.

this customer has asked us to find a replacement locking sliding glass door handle i have ordered 2 already 1 from swisco & one from you guys they both are too small 82-238 & 82-086i am including some pics as well this is for the army / national guard recruitment mobile unit & i have b ... (cont.)

The lock and latch from the sliding glass door in the pictures needs to be replaced. The lock has fallen out and the lever that latches the door has broken. The only markings on the door I can find are SGD-LC25-96 X 82. The mechanism/handle is 7" high.

Here are photos I was unable to attach to my previous message.Louise

door is 2" thick and screws are 5" apart. says made in New Zealand with letters IT on lock mechanism. what do you suggest?

I have a 2013 Thermotwin Glass Sliding door and the handle has broken as shown in the following pictures. Do you have a replacement handle or something that would take its place?Thank You,David

I ordered the 82-238 to replace my broken mortise lock along with what I think is an 82-080 handle but they don't seem to fit together. What I think was the 82-080 came with a striker and a different double hook lock. Should I re-order the 82-080 that doesn't have the double hook lock? ... (cont.)

I'd like to replace the outside lock handle on this door with a keyed lock handle. The door is by Certainteed from the early 2000's.

Only the sliding glass door handle is broken apparently because of a broken screw and the lock works well. There is about 5 inches between the two interior screws with the handle mechanism falling half way between on the interior of the door. It has a nickel finish

Hello, We just purchased the 82-081 handle set for patio doors. The hand set fits like it should. However, the mortise lock holes do not line up with the handle set. Do you have any suggestions? Pictures attached. Do you have a mortise lock set that fits the handle?

Need to return other parts

I am looking for the 2 replacement door handles and all parts that go with my hurricane proof sliding glass door. My door has three handles. The handle is 7" high. Two on the inside and one on the outside and the outside of the other door does not have a handle. I am ok with anything you have as lon ... (cont.)

I need the central latch (doorLatch.jpg & doorLatch2.jpg). The top & bottom latches are good. They are ganged to the central latch via a flat rod that mates with pins. You can see the pins to the left of the hook on doorLatch3.jpg. It looks dimensionally similar to https://www.amazon.com/gp/product ... (cont.)