Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

need to buy a bunch of this balance but cannot find the code on it. Your help will be very much appreciated. Thank you

Hello Are you able to assist with locating the correct balance and components for the photos attached? One balance has the number 2640 and it is 27" long and 3/4 wide. The clear plastic thing is about 5/8" wide, 6/8" in height. 1.5" length. Let me know if you need additional photos measurement ... (cont.)

Please help confirm channel ID! It's stamped 2640, measures 27" and 9/16 wide. I'm leaning towards: 27" Series 380 Channel Balance (Product Code: S380-27) with the 19-005 top and 15-005 (1" deep) bottom fittings. Thank you!

Hi Looking for 2 window balancers marked 26-4 HA2 CMC 24. It measures from metal end to metal end 27 inches. The metal is 1/2 inch wide.

It has the numbers 27" 40lbs. One of the pictures it shows a shoe that needs to be on the end of the balancer.

Hi, this channel balance is 27 inches long (the metal part). it has the following marking: 26DS 32, also between the numbers it says BSI NL

I need to replace two vertical balancers in two windows 30 x34 " inches The balancer shaft has this number on it 26405 with B.S.l. perpendicular across the bottom of the numbers. The frames are metal installed in 1989. I can not remove the windows from the frame like the newer Milgard plastic ... (cont.)

Windows balance spring Numbers on balance 26 9 JW CMC 7 Measures: 27" length, spring space width 1/2" Spring space depth 5/8"

Hello, I have Milgard windows and a few of the balancers broke. I want to be sure I select the correct replacement parts. Attached are photos of one of the balancers. Marking shows 26 4 JW CMC 7. It measures 27in long and 5/8 wide. Please let me know if there is any additional info you need in helpi ... (cont.)

1/2" wide 27" long Need to identify and replace the window balances shown. I believe the markings are 26 4

27 in.26 3 in 5 cmc 43I need the sash guide also.Thanks

Hi, I recently had one of my window channels break and I'm unsure as to which model I am supposed to buy, and where to buy it. I've attached a picture of the side channel and codes that are on it in hopes that you can help to guide me purchase the correct replacement. I've attached a picture of th ... (cont.)

I need to get some new channel balances. It's 27 inches long(metal). With hook. The end has little wings.

I need to replace some channel balances I think the measurements are: 17 pounds, 1/2" channel width, metal length of balance is 27", the fittings have wings on both ends, I think the bottom shoe is slightly more than an inch. The marking on the balance shows "26 3 BSI 00" Please see pictures. ... (cont.)

They are Marked 26 5 JO Caldwell and They are 1 inch depth across the bottom bracket by 27 long and a half inch wide Thank you

27"length stamped 26 3 Kinro windows I need to replace 1 balance please Aaron

The plastic ends ar 15/16 inch wide at the widest part of the tabs. The metal track is 1/2 inch on the narrow side and 5/8 on the wide side. The top of the spring does not have a pulley and it is anchored inside of the metal channel. On the backside of the metal channel there is an imprint that read ... (cont.)

Hi, the closest match i could find was a 27" series 385, please confirm, or do I need something different? I have 2 windows that the piece has come off and windows won't stay open and shimmy to the point of coming out?

1/2" width 27 length Outside track is stamped with 26 4 IW CMC 11 Any assistance would be greatly appreciated. -Robert

Hi there, I'm looking to replace 2 channel balances for my windows the writing on both is (26 4 10 Caldwell) they measure at 27in. Thank you!