Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

Need a replacement window balance for leaded vinyl window. Window is heavy. Stamp on current balance is 2690 30. Balance is 27 inches long and 9/16 (1/2)" wide. You don't have a 2690 30 so, which balance should I order from you?

This is 1/2 " by 27". Left side of a non tilting window.

Hi I'm trying to find replacement for my window channel balance . On mine is stamped the next numbers : 26-4 FK5 CMC 43 , and is 27 inch long . Is it compatible with yours : 27" Series 380 Channel Balance S380-27 option: 2630 Thanks . Mike (Image # 1273 has the part numbers on it ) ... (cont.)

I measured the depth without thickness of the tab (wing) thickness to be 1" 3/32. Tab thickness is about 3/16". Is 15-004 correct?

Hi, I don't know if I need to replace my channel balancers or just order the clips that go with them for the window, or maybe both? I have 2 windows that the balancers have come off of. 1 window it's the right side & the other is the left. Can you help? Also, the length of the metal on the balancers ... (cont.)

Do you guys have replacement for this balance.

Hello, Unfortunately I am not sure what part to order since there are no markings, names or number on it. The channel is 27" and 1/2" wide. Not sure how heavy the window is. The house was built in 2002 which is when the windows were installed. Thanks! Regards, May

The metal part is 9/16 wide and 27" long. The nylon ends both have wings.

hi there -- the metal track is 1/2" wide and 27" long (metal only). Markings on the track say 26 4 LQ CALDWELL. Those are the only markings I can find. The plastic ends have wings (photos attached). I measure the bottom one to be 1 1/16" deep. thank you!

My window balancer is 27 inches long the only markings on it are 26 4 GQ CALDWELL. I will need two balancers.

27" Channel Balance, what size do I need?

Hi, I need replacement 27 inch Milgard chanel balance, need 24 of them for 12 windows Makings: 26 4 HT CMC 4

See attached photos of the balance I have. Can you tell me what part number of yours is a match. I'd be needing 2 pcs

I need help with a replacement for a broken window balancer. Please tell me what part to order from you. Window weighs 21 pounds. I also inquired about another window in reference number D148406. Thank you Sue

My window has 2 different balancers with 2 different part numbers probably because someone worked on it in the past. I will replace them both so they match. The window weighs 23 pounds. Which part should I order from you? I also need help to identify a 33" balancer. I will send a separate message ... (cont.)

The parts number is in the channel balance are 2640

Hi- I need to replace 2- 26 4 HR Caldwell balancers from a Milgard window. My current balancer is 1/2" wide. I used your site, but your parts are numbered differently (SXXX). This is a non-tilt window. I am attaching photos. Thanks for nay help you can provide. -Scott

Need 4 of these window ballasts for slide up/down windows?

Sir/Ma'am:I'm trying to purchase and replace two window non-tilt balances and I just needed a bit of help ID'ing some parts and confirming what I need. The balances themselves measure 27" for the metal and are marked 2630, looking at them I am fairly certain that I need either S380 or S385 to repla ... (cont.)

Hello, I have a broken channel balance and from a similar post I believe it is a swisco part. Could you help me identify the correct replacement part number? Please let me know if additional pictures are needed. It is 27" The identifier stamped on the part is 26 4 CV cmc 7 Thanks! Gabriel ... (cont.)