Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

The little rope inside broke.

looks like a 26" Series 385 Channel Balance on the metal it says......26 4 HX CMC 11 ca u tell me which replacement part I need? thanks

I have a 26 3 DR Caldwell channel balance, the metal channel is 27" long, bottom shoe 1 3/32" wide, the top is winged. I believe I should order the 385 Series, but what option? I have a double pain vinyl window 33 1/4" wide by 27 7/8" tall.Thank you and best regards, Allan

Hi, Trying to identify this balance to order a replacement, It measures 27" x 1/2" and you can see the Milgard numbers in last picture. I have replaced them before but in that case Milgard had sent them under warranty. Please let me know. Thanks, Jon

It's been a while I've shopped for this and other sizes all with the same ends. If you can verify from the five photos I was allowed to upload the correct replacement ID/item I'd appreciate it, I'm passing on this to a new SWISCO customer and want it to be right.

Do you carry this replacement balance?

I'm looking for a pair of non-tilt window balances and top sash channel balance guides for one of my Milgard windows. The balances are identified with "26 5 JV CMC 2" stamped on them and the metal channel measures 27" long. Looking at your website, I believe I've identified the balances as 27" SER ... (cont.)

I have a Cladwell 26 4 window balance that is 27" length. What would I be ordering as its replacement?

Hi, Although the "26" suggests 26 inches, I measured the length of the steel profile to be 68.5cm = 27 inches. I hope the photos help to clarify. Please let me know if you have replacements and what it would cost. (Single side or pair) Thanks Josef

These are non tilting out windows, and the length of the channel metal from one end to the other is 27". Hope to hear from you soon so that I can place the order.

Hello, I have a sash window balance I need to replace. The metal part is 27" long and it has plastic white bits at the top and bottom. Has some kind of pulley mechanism. It says "2630" on the metal and in small print "B.S.I." and in even smaller print "RH" The images are of a "working" one. I have a ... (cont.)

Need help identifying replacement part, The channel shows 26 4 HX CMC 11, metal channel 27" long, 1/2" channel width non-tilt window. Photos are attached

Would you please confirm whether this is the 380 or the 385? Thank you

I am having a hard time determining what Series Type of balance I have. They are 1/2" wide and 27" long. From other threads I believe I should have the 2650 option. Thanks for the help!I also have an issue with the part that the balance slides and connects to. It is the plastic piece that is screwed ... (cont.)

Length is 27"

26 4 BR CALDWELL stamped on back. Metal channel is 27 inches long,and 1/2 inch wide. Shash is aprox.18.2 lbs.

Hello, Looking for replacement for a broken channel balancer for a Milgard Non-tilting window, weighs 24 lbs 8 oz, the numbering on the balancer is 26 5 AW CNC 2, measured the channel is 27in long. Can you please let know what part # this corresponds too? Thanks

Hello - To the best of my knowledge I followed the instruction video on how to install non-tilting window sliders. Maybe I'm the only one who thinks so, but I get the feeling those instructions could use some work. I ordered and received two channel guides, to replace the old ones, only one ... (cont.)

Need replacement window spring. Part number inscribed on side of spring is "26 3 HP Caldwell". The metal part of the spring casing is 27".

Looking for help identifying the correct replacement Assembly. Only identifier is 26 4 LN printed on back. Frame measures 27" from end to end.