Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

I need 4 of these balance rods for 2 mil guard windows.

Hello, I am looking for replacement balances for my Alpine windows. Marks printed are 26 4 FO CALDWELL. The measurement is 27" (just the metal part). Which replacement part do you recommend? Thanks Kevin

Aloha, I have tried submitting the form for identifying a part. However, I kept getting an error message. I tried 2 other browsers and the same thing happened again. So I am sending you this message with photos. This is a new post. I have ordered with you before and am grateful for your assistan ... (cont.)

The sash weight range is not on the balance spring. How can I determine the sash weight range? Is the sash weight the weight of the sliding window itself or the force it takes to slide the window up/down? Do I need to 1/2 the weight of the sash weight to determine the correct weight ran ... (cont.)

I purchased this channel 27" 385 w/ option 2640 about 2 years back: discussions/dp93820207031899000-77-37806 The weight of the window is 19lbs (low end of option 2640 weight limit). It worked but recently failed - looking at the photos of both channels you can see the top rods holding the ... (cont.)

I have two different balances that have gone out, if you're to be identical with the exception of the marking. I have been told they are for different weight windows, I do not know how much they weigh, hopefully you can help me figure it out. I have included the markings in the pictures, howe ... (cont.)

27" long 1/2" wide channel with spring and cord per attached images. Need replacement for both side of the vertical sliding window. Instruction to remove window and mount new channels.

I need to replace some window balances. Looks like S385-27 is the correct choice. It is stamped 26 4 Caldwell jm but there are no other markings related to weight. Can you assist. Jim

Please help me identify my channel balance. The metal parts are 27" x ½". I believe that it has 19-005 and 15-005. It has "26 4 BW CMC 4" printed on it.

26 5 EW CMC 10 is printed on the channel balance, what is the replacement part number and is there a better quality replacement channel rebalance that the original? the length is 27" and 1/2" in width. I have 18 windows that will need 2 each as all of the windows need new ones as the original starti ... (cont.)

Length 27" Width 1/2" Markings 26 4 FO Caldwell Markings 26 3 IO Caldwell Sash Weight 18 lbs. Shoe depth 1 3/32" Believe I need Product code S385-27 option 2630

Hi

Which balance do I need? The code stamped on the broken channel balance is "26 9 JV CMC 7." I measured the length and it's 27 inches for just the channel and 9/16" width. It seems like this is the correct one but I'm unsure of the weight.

Hi, I wrote few weeks ago to ask if I can replace a cord in widow balance and was told that I'd need a new balance Series 380 or Series 385, depending on the size of the bottom shoe). So I just want to confirm that this would be the right part to order: S385-27. I assume I need to replace both bala ... (cont.)

please see the pics and help me find replacement parts. The sashes are stamped "26 5 EX CMC 7" and weigh 25 pounds. Thank you!!!

The current balancer is 27 inches in length. The stamp reads " 26 5 IW CMC 11". Which balancer would be my best option? Thank you for your help!

What balance do I need

Hi, I need help finding replacement springs. I have included a couple of photos. The old part is marked 26DS, sideways BSI or BSL (not sure) and then NL 32. I have included the end fittings in the photos too. The length of the metal is 27", the width is 1/2" and the depth is 5/8". I also need the ta ... (cont.)

Hi! These are .5 inch wide, 27 inches long. I can't seem to find the correct match for the connectors. Any help would be very appreciated.

I have Milgaurd Non-tilt windows and are replacing the window balances, the 27" balance ( 1//2" wide ) is stamped with the number ( 26 9 CR CALDWELL ) the exact model would be a " series 385 but unsure of the rating as the stamped number does not match any of your post numbers ? Regards Mark ... (cont.)